ALLNET Touch Display Tablet 18 inch PoE with 4GB/16GB, RK3566, FullHD Android 11 black

Set besteht aus 2 Kabelpeitschen mit Buchse auf Lan/Ethernet Kabel mit jeweils einmal DC/Hohlstecker Buchse und einmal Stecker 5.5mm / 2,1mm. Passives PoE, kein echtes PoE - Stromquelle muss auf Gerät ausgelegt sein und das Gerät muss einen Hohlstecker als Strom-Eingang haben.

Highlights: support IEEE802.3, IEEE802.3u, IEEE802.ab,IEEE802.3af, IEEE802.3at and LT PoE 90W 1 Port 10/100/1000 Base-T (Data) for connection to a switch, and 1 Port 10/100/1000 Base-T (Power/Data) for connection to a PoE Device (PD) Automatic detection of whether the connected device is PoE capable   With the ALLNET ALL048900V2 High Power PoE Injector you install your PoE-enabled IP devices such as wireless access points, VoIP phones and much more totally independent of existing electrical outlets.   So you can choose the best locations for example WLAN access points installations in a building regarding the wireless technology, without having to worry about power cabling.   Non-PoE switches can be efficiently „upgraded“ with Power over Ethernet, especially when you only need a few ports with PoE power supply. Here the ALL048900V2 saves the expensive purchase of a PoE switch.   The ALLNET ALL048900V2 supports the IEEE802.3af standard with a power of 15,4 Watt, the IEEE802.3at high power standard with 30 Watt and the LT PoE with 90 Watt power.   The ALL048900V2 must not be configured. It has an RJ45 jack and an RJ-45 output connector, which are connected to this switch and the end device to the PoE injector. The cable length can here, as usual in Ethernet, up to 100 meters between the switch and terminal in total.   The compact design and the metal case of the ALLNET ALL048900V2 can be very inconspicuous installed and is extremely robust.    Technical Details:   Element Spezification Standards: IEEE802.3af Power over Ethernet IEEE802.3at Power over Ethernet enhancements LT PoE 90W IEEE802.3 10BaseT IEEE802.3u 100BaseTX IEEE802.ab 1000BaseT Ethernet ports: 1x RJ45 10/100/1000Mbps for connection to passive switch or hub 1x RJ45 10/100/1000Mbps for connection to PoE device LED indikators: Power / PoE Act / Status Power input: 44~57V Power consumption:   System: 5W (Max.) LT PoE++: up to 90W   Attached power adapter: Input: 100~240VAC Output: 56VDC/2A, 112W (Max.) Case: Metal case, wall-mountable Dimension: Length/Width/Height: 102 x 75 x 23 mm Weight: 280g (o. Netzteil und Verpackung) Environment: Temperature operating: 0 ~ 40 °C Humidity operating: 10% ~ 90% (non-condensing) Temperature storage: -25 ~ 90 °C  Marks: FCC Class A, CE

ALLNET PoE Injector Gigabit PoE & PoE+ (15,4W/30W) / plastic housing / "ALL0488v6   Highlights: PoE injector according to IEEE802.3af/at with max. power of 30W 2x RJ45 Gigabit Ports PoE Output 55VDC@30W Midspan PoE PIN's 4/5 (+) and 7/8(-) internal power supply unit compact design incl. 1.5m power cable with IEC-C5 to IEC-CEE7 protective contact cable NEW: Wall mounting capable Intelligent power supply via network without switch With the ALLNET ALL0488V6 Power over Ethernet Injector you can install your PoE-enabled IP devices such as WLAN access points, VoIP phones and much more absolutely independent of existing power sockets. For example, WLAN access points can be installed in the most ideal locations in a building without having to worry about power cabling. Switches that are not PoE-capable can be "retrofitted" with Power over Ethernet at a reasonable price, especially if only a few ports with PoE supply are required. Here, the ALL0488V6 saves the purchase of a PoE switch. The ALLNET ALL0488V6 supports the IEEE802.3af & IEEE802.3at standard with a maximum power of 30W Watt. The ALL0488V6 does not need to be configured. It has an RJ45 input socket and an RJ-45 output socket, which is used to connect the switch and terminal device to the PoE injector. The cable length here can be up to 100 meters between switch and terminal device in total, as is usual in Ethernet. Due to its compact design, the ALLNET ALL0488V6 can be installed very easy. It has an internal power supply and supplies the PoE voltage on pins 4/5 (+) and 7/8 (-). Technical Details: Element Specifikation Standards: IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-Tx Fast Ethernet IEEE802.3ab 1000Base-T Gigabit Ethernet Support terminal equipment with IEEE802.3af/at, PoE++ RoHS Compliance WEEE Compliance Ethernet Ports: 1x RJ45 10/100/1000 Mbps for connection to switch or hub 1x RJ45 10/100/1000 for connection to PoE end device PoE Output: PoE IEEE802.11af/at, Power pins: 4/5(+) 7/8(-) Power supply: 100 - 240VAC, internal power supply / Output: 55V/550mA incl. connection cable earth contact on IEC320-C5 "Kleeblat/Micky-Mouse" approx. 80cm length Power consumption: 30 Watt maximum with connected PoE end device AC Surge Protection: 1.0KV (5P/5N) L-N 1.2/50 (8/20) Tr/Th us 2.0KV (5P/5N) L-PE 1.2/50 (8/20) Tr/Th us N -PE Housing: Plastic housing Mounting: Wall-mounted Dimensions: length/width/height: 140 x 63 x 33 mm Environment: Operating Temperature: 0 ~ 40 °C Operating Humidity 10% ~ 90% (non-condensing) Storage Temperature: -20 ~ 90 °C Storage Humidity: 10% ~ 90% (non-condensing) EMI: FCC CFR47 Part 15 EN55024 EN55032 EMS: IEC61000-4-2(ESD) ± 6kV(contact), ±8kV(air) IEC61000-4-3(RS) 10V/m(80MHz~2GHz) IEC61000-4-4(EFT) Power Port: ±2kV; Data Port:±1kV IEC61000-4-5(Surge) Power Port:±1kV/DM, ±2kV/CM IEC61000-4-6(CS) 10V(150kHz~80MHz) Immunity: IEC60068-2-6(Vibration) IEC60068-2-27(Impact) IEC60068-2-32(Free Fall) Marks: CE; FCC

Highlights: Support 1*Multigigigabit 10G PoE port (1G/2.5G/5G/10G) + 1*10G (1G/2.5G/5G/10G LAN) RJ45 port; Support IEEE802.3af (15.4w), IEEE802.3at (30w) and IEEE802.3bt (90w) Support power supply 100-240VAC Metal housing, IP20 protection rating, -20 ~ 50°C working temperature Support port surge protection: Differential mode 2KV, common mode 6KV; ESD: Contact 6KV, air 8KV. The ALLNET PoE Injector ALL-PI103MG-BT90-10G is a powerful multi-gigabit PoE injector that provides up to 90W output power per PoE port. The port supports automatic adaptation to different speeds (1G / 2.5G / 5G / 10G), allowing it to adapt flexibly to different network environments. The voltage range for the input is between 100 and 240V AC, while the operating temperature range is from -20°C to +50°C. Thanks to a robust industrial chip design, the PoE injector is particularly resistant and equipped with ESD overvoltage protection. It fulfils all relevant standards such as FCC, CE and RoHS, which ensures a high level of reliability and safety. The sophisticated hardware design ensures stable, uninterrupted operation, ideal for automation systems. The compact housing can be mounted both on walls and tables. Typical applications include PTZ cameras, compact computers, all-in-one devices, digital signage displays and other network-based systems that require high performance and reliability. Usecases: Surveillance systems This product is often used in the field of network camera surveillance, as it can provide both the data connection and the power supply for network cameras. WLAN networks The product is widely used in WLAN network projects, such as in parks or large open spaces. The PoE injector can provide wireless access points (APs) with both power and a stable data connection. Technical details: Specification Product Name ALL-PI103MG-BT90-10G Port 1*10G PoE port + 1*10G RJ45 port MultiGigabit 1G/2.5G/5G/10G PoE Specification PoE standard: IEEE802.3af/ IEEE802.3at/ IEEE802.3bt Single Port Max: 15.4W (IEEE 802.3af) Single Port Max: 30W (IEEE 802.3at) Single Port Max: 90W (IEEE 802.3bt) PoE Port Output Voltage: DC 52V PoE Power Pin: 1/2-; 3/6+ Or 4/5+; 7/8- Network Medium 100Base-TX: Cat5 or above UTP(=100m) 1000Base-TX: Cat5 or above UTP(=100m) 10000 Base-TX: Cat6 or above UTP(=100m) Indicator (PWR) On: Powered On Off: Powered Off Power Input Voltage: AC 100-240V Working Frequency: 50/60 Hz Supply Power: 52V1.73A/90W Working Environment Working Temperature: -20~50°C Storage Temperature: -40~85°C Humidity: 5%~95 % (non-condensing) Industry Standard EN61000-4-2 (ESD) IEN61000-4-5 (Surge) EN61000-4-3 (RS) EN61000-4-6 (CS) EN61000-4-4 (EFT) Physical structure Protection Grade: IP20 Install: Wall Mounting Product N.W: 0.486KG Product G.W: 0.712KG Product Size (L*W*H): 187* 95*40 mm Package Size (L*W*H): 245*190*60mm Package List 10G 90W PoE Injector: 1pcs User Manual: 1pcs Certificate, Warranty Card:1pcs

Rock Pi 4 zbh. USB 3.0 Male Type A to A for USB Firmaware upgrading, USB gadgets and Android ADB debug

<p>Bezel&nbsp;f&uuml;r&nbsp;18&quot; inch tablet, improved version with wall closure and slip-in.</p> Advantages compared to the predecessor:</strong></p> <p>- Tablet and mounting frame disappear into the bezel</p> <p>- Magnets in the bezel and not screwed on</p> <p>- The bezel has been lowered/flattened towards the touchscreen&nbsp;</p> <p>- Single product, bezels can be purchased individually</p> <p>- Different standard colours black, silver, white&szlig;</p> <p>- Custom colours bronze, gold, RAL colours&nbsp; can be ordered from 100 pieces&uuml;ck</p> <p><strong>Product:</strong></p> <p>Colour black, narrow</p> <p><br /> The cover is magnetically fixed to the installation frame. The magnets must be mounted in the panel&nbsp;</p> <p><u>Please bear in mind that the tablet speakers are located on the back of the tablet and the quality and volume of the sound options will be reduced as soon as the tablet is installed in a wall.</u></p> The tablet is screwed to the frame via the vesa holder and then mounted in a drywall or wooden wall. Walls are of course also possible, but are only recommended to a limited extent due to possible heat accumulation. <p><strong>Dimensions of the installation frame:</strong></p> <p>mm</p> <p><strong>mm</strong></p>

Fitting installation frame for 18 inch tablet. Single frame for installation in walls, tables, furniture, etc. Flange rests on top. Tablet protrudes approx. 2 mm from the frame. This frame is especially suitable for our cover panels. Dimensions: mm incl. flange of 18mm Cut-out: (+2mm on each side to ensure air circulation) Depth should be at least 40 mm.