ALLNET ALL3419 / IP Building-Autom. 3x I2C, 1x USB, LAN/WLAN

The ALLNET NTP Server is a time server based on the NTP (V2, V3, V4) / SNTP protocol. It obtains standard UTC time information from the GNSS satellite receiver and transmits this information on the network. Devices that need time signals in the network, such as computers and controllers, can synchronize with the standard clock signal to realize the network timing function The standard clock signals are transmitted through the TCP/IP network and support point-to-point and broadcast transmission modes. The product is easy to operate. Just connect the GNSS satellite antenna and the whole network can synchronize the time. The product has small size and structure, convenient installation, extremely low power consumption and is plug and play. Technical data: Up to 6000 visits per second Webui interface, convenient and fast management LAN synchronous time accuracy: 0.5-2ms Internally integrated GNSS satellite receiver with high precision time measurement Supports GPS, Beidou, GLONASS and QZSS NTP v2 (RFC 1119),NTP v3 (RFC 1305),NTP v4 (RFC5905) SNTP v3 (RFC 1769), SNTP v4 (RFC 2030) Supports MD5 information verification Supports server and broadcast working modes; Ethernet port supports 10 / 100M, full duplex and half duplex and supports auto-negotiation mechanism Supports user-defined MAC addresses NMEA0183 is transmitted via TCP protocol Compact structure and convenient installation Power consumption is only 1W Industrial operating temperature range

isolated switching output for ALL3000/3500/400x/4500/5000optoelectroniccoupler, with max. 20 mA switching current

Temperature sensor compatible with ALL3000/34xx/3500/ALL400x/4500/5000 Measuring range -55 to +80 °C, 13-bit ADC with a temperature resolution of 0.03125 °C Temperature accuracy of ± 1 °C from -25 °C to +100 °C with 1 m connection cable Exclusively only one of the following sensors possible per sensor port! ALL4454, ALL4432, ALL4421, ALL4590, ALL4532, ALL4552, ALL4522, ALL3005-6, ALL3015,ALL4006, ALL4506-7  

Temperature sensor for ALL3000/34xx/3500/400x/4500/5000 WATERPROOF & salt water resistant Measuring range -55 to +125 °C Resolution 0.06°C 1m silicone cable with shrink cap with RJ45 Keystone socket "Art. 88971" The scope of delivery also includes 1x 20m patch cable.  

Threshold switch for vertical installation (pen with float-ring) made ??of polyamide, resistant to gasoline, oil, brake fluid and much more. 1 m connection cable for ALL3000/ALL4000

Compatible with ALL3000/34xx/3500/400x/4500/5000 Fluid threshold for horizontal installation (hinged float) made ??of polyamide, resistant against gasoline, oil, brake fluid, etc. With 1 m cable

Compatible with ALL3000/34xx/3500/400x/4500/5000 passive infrared motion detector reliable motion detection extremely high noise immunity changeable lens is standard 90° NC tamper switch manual adjustment range (up to 15 x 15 m) creep with counter with 1 m cable

Multiplexing module hub for star-shaped distribution of up to 8 sensor modules for ALL4500/ALL5000. For the operation of the ALL4404 a base station/central unit is required. With the ALL4404 you expand the possible sensors by a factor of 8. A maximum of 1x ALL4404 can be connected per master port on the central station. The maximum cable length from the I2C sensor port is max. 100m and is NOT extended by the ALL4404 i.e. the maximum cable length through the hub is still 100m. Application example:  ALL4404 (Single) ALL3419 ALL3500 ALL3505 ALL5000v2      

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C   Temperature sensor in desktop-/ wallmounting case   measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C Temperature sensor in desktop-/ wallmounting case measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights: new flat desktop / wall mount case made of aluminium I2C bus for multiplexing use measuring range -40...+125 °C, 0...100 %RH resolution temperature 0,01 °C, resolution humidity: 0.01 % Measuring accuracy Temp in whole range approx. +/- 0.6° (Typical: -20 + 90° = +/- = 0.2°) Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1,5%) ONLY COMPATIBLE WITH ALL34xx/350x/4500/5000 Angle brackets for wall mounting Measure, control and regulate automatically and independently ALLNET has been pursuing the concept of intelligent control of building technology processes via network and Internet for years. Intelligent building technology not only offers more comfort, but also actively promotes the saving of energy costs. Centrally controlled and accessible via network / Internet, ALLNET building automation products enable intelligent building technology independent of time and location.   Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Compatible with ALL3000/34xx/3500/400x/4500/5000 counter in metal case, wall mount option it counts how often the contact has been closed counter frequency: 1000 Impulses/Sec 6-digit counter (0...999999) with 1 m cable

• Compatible to ALL3000/34xx/3500/400x/4500/5000 • Contact counter in metal housing • Counts how often a contact has been closed. Max counting frequency: 1000 pulses/second • counter 6-digit decimal (0 … 999999) • 1 m cable

Highlights: Compatible with ALL34xx/3500/4500/5000 4-port relay output in metal desktop/wall-mounted housing switches 4 relays with ON contacts 250V/10A (no longer compatible with ALL3000/ALL4000) The ALL4427 is a powerful 4-port relay output in a robust aluminium housing that is ideal for controlling various electrical loads, whether for controlling lights, pumps or other devices with a maximum current requirement of up to 10 amps per relay. With a voltage of up to 250V per switching contact, the ALL4427 offers reliable performance for demanding applications. Compatibility and versatility: Compatible with models of the ALL34xx/3500/4500/5000 series, but no longer with ALL3000 or ALL4000. The connection is made via 2x RJ45 sockets, allowing the device to be easily integrated into existing networks. Handling and mounting: The aluminium housing is durable and resistant, ideal for harsh environments and use in demanding projects. The integrated wall mounting bracket enables simple and stable mounting on walls or in the control cabinet. Multiplexing for extended applications: Multiple multiplexing allows several modules to be operated simultaneously on one line, which enables flexible expansion of the relay control for more extensive setups. This 4-port relay module offers a reliable solution for controlling electrical devices and is an ideal choice for users looking for flexible application options and easy installation. Technical details: Element Specification Sensor type 4-fold relay with ON contacts 250V/10A Chip PCF8574 Connection: 2x RJ45 (I2C bus) Multiplexing: Adjustment wheel for ID LED indicators: 1x PWR, 1x BUS, 4x contact output How to use: Metal walking Environment: Temperature operation: -45 ~ 90 °C Humidity operating: 10% ~ 85% (non-condensing) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensing) Labelling: CE, RoHS Dimensions: 79 x 50 x 24 mm (length x width x height) Weight: 230 grams (without packaging and accessories) Packaging contents: 1x ALL4427 4-fold relay 1x 1m connection cable

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4429 Combination sensor has a measuring range of 0 to 1023 mbar, -40 to +80 °C and 0...100 % RH Combination Sensor of air pressure/humidity/temperature in desktop-/ wallmounting case measuring range of 0 to 1023 mbar / -40 to +80 °C (resolution 0,01 °C) / 0...100 % RH (resolution 0,5%) Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 not compactible with ALL3000/ALL5000 Technical Details: Item Specification Sensor type air pressure, humidity, temperature air pressure measuring range: 0 to 1023 mbar Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip BMP085 + SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4429 Combination sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.  

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting   Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4432 Brightness sensor indicates the brightness as value of 0 to 100.   Brightness Sensor in desktop-/ wallmounting case   measuring range of 0 to 100 Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Brightness analog 16bit measuring range: 0 to 100 Chip ADS1100A2 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4432 Brightness sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Compatible with ALL34xx/350x/4500/5000/3692 4-Port contact input in metal case with wall mount option  4Port contact input (isolated) result of open contacts is "1", closed contact is "0" - possible solutions: idle door contact with puls stretching NOT COMPATIBLE WITH ALL3000/ALL40000.

Compatible with ALL3000/ALL34xx/3500/400x/4500/5000 volt meter in metal case housing with wall mount/desktop option detect when power fit or not 4-phase, for AC voltage 220...240V isolated over relay connections: 1x RJ45 INPUT / 1x RJ45 OUTPUT

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4452 PIR Movement detector has a max. detection angle of 92° and a max range of 8 meters. Movement detection Sensor in desktop-/ wallmounting case max. detection angle of 92°, max. range of 8 meters Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type   PIR movement detection   measuring range: max. detection angle of 92°, max. range of 8 meters Chip PCF8574 Interfaces: 2x RJ45 (I2C Bus) Multiplexing:   dial wheel for ID (8), see note below   LED Indicators: 1x PWR, 1x BUS, 1x Detetct Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4452 PIR Movement detection sensor 1x connection cable   Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more thanone sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

  Highlights:   new compact aluminum desktop- / wall mounting case I2C Bus for multiplexing use either in black or white available angle fixings for wall mounting       Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4454 smoke detector/ sensor can also be used for detection of gases.     Smoke detector/ Gas sensor in desktop-/ wall mounting case   reports of smoke and gas Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x)   Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.     Technical Details:   Item Specification Sensor type Smoke-/ Gas detector measuring range: 0 to 100 Chip ADS1100A3 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non-condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4454 smoke detector / Gas sensor 1x connection cable

Hightlights: new compact aluminium desktop- / wall mounting case I2C Bus for multiplexing use either in black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4454 smoke detector/ sensor can also be used for detection of gases. Smoke detector/ Gas sensor in desktop-/ wallmounting case reports smoke and gas Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Smoke-/ Gas detector measuring range: 0 to 100 Chip ADS1100A3 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4454 smoke detector / Gas sensor 1x connection cable Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

WLAN power socket, switchable via network / IP with performance measurement (positive/negative) • Allows switching of connected consumers (up to 16A resistive load) via integrated webserver - new release 3.2 • 10/100 Mbit RJ45 network interface • IEEE802.11b/g/n Wireless LAN with 300 Mbps • With integrated power plug socket • for 200 - 250 V AC • Voltage and consumption measurement • Time controlled, programmatically or manually switching The ALL3075v4 network power socket allows switching of connected devices via network or IP. The ALLNET device acts like an adapter between power outlet and electric consumer. Connected to a computer network, the ALL3075v4 is accessable via its own IP address. Both, con guration and operation can be done with any network based OS. No additional software is needed, the only requirement is a web browser. The ALL3075v4 measures and stores the energy consumption of any connected device. The switching operations can be done manually, based on time, consumption or by individual programming. Several devices of the The ALL3075v4 can also be combined to a grid. The network power socket works perfect with various ALLNET automation solutions, like the ALL369x Powermeter or ALL3418v2, 3419, ALL3500, ALL3505, ALL4500 and ALL5000 central units. The ALLNET ALL3075v4 adapter is based on the brandnew Release 3.2 user interface. In addition to several visible innovations, Release 3.2 offers for the rst time even the possibility to integrate multiple ALLNET sensors or actuators quickly and easily via JSON. This allows central administration of multi-site based measurement data. This supports administrators with a perfect clarity and facilitates their work dramatically. In additon to the RJ45 network interface the ALL3075v4 also offers a Wireless-N interface with a maximum transfer-speed of 300 MBit. This allows easy integration into wireless networks and seamless usage and con guration from every smart phone or tablet. The ALL3075v4 can be con gured for client or access point usage. The "server control" function allows easy control and even reset of connected PC or server systems. Server control sends automated ping requests to the connected server. If the PC or Server system does not answer in a pre-con gured time, the power outlet will quit the transfer and reset the connected device to restore functionality. Technical Details: Network: 10BaseT 100BaseTX Network connector: RJ45 Wireless LAN / WiFi: 2.4 GHz Wireless N, 150 Mbps 1T1R WiFi chipset: Ralink RT3352 WiFi Securityt: WEP 64/128bit, WPA, WPA2 Standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Protocol: HTTP/HTTPS TCP/IP Management: via web browser, XML/JSON supported OS: all network supporting OS supported voltage: 200 - 250 volts switching current: max. 16 amps = until 3680 ohmic load power measurement: consumption (negative) feed-in from solar panels (positive) Housing: PVC with European Socket Environment: working temperature: 0 ~ 40 °C working humidity: 10% ~ 85% (non condensing) storage temperature: -20 ~ 60 °C storage humidity: 5% ~ 90% (non condensing) dimensions: 125 x 68 x 40 (60) mm weight: 200 grams (only the adapter)

Highlights: Enables switching of the connected load (up to 16A) via the integrated web server- New release 3.2 Wireless LAN according to IEEE802.11b/g/n with 300 Mbps & 10/100 Mbit RJ45 network connection German earthing contact plug/socket for 200 - 250 V alternating voltage Switching time, programme-controlled or manually possible The ALL3073v3 network socket can be used to switch electrical devices on and off via a computer network. The ALL3073v3 acts as an intermediate plug between the power socket and the electrical consumer. It is integrated into a computer network and receives a unique IP address. It can be configured and operated via any web browser from a PC, MAC, webpad or smartphone, regardless of a specific platform or operating system. No additional software is required. The switching operations can be programmed manually, time-controlled, etc. Several ALL3073v3s can be switched independently of each other. They also work together with other ALLNET automation solutions, such as ALL369x Powermeter, ALL3418v2, ALL3500, ALL3505, ALL4500 or ALL5000. The ALLNET ALL3073v3 adapter is also equipped with the heavily revised user interface 3.2. In addition to numerous innovations in the user interface, Release 3.2 also offers the option of quickly and easily integrating multiple ALLNET remote sensors and actuators into the control interface via JSON for the first time. This means that the sensor data can be managed across locations via a central interface, resulting in significantly greater clarity and simpler administration. In addition to the wired 10/100Mbit/s RJ45 network interface, the ALL3073v3 also has a wireless LAN interface in accordance with the IEEE802.1b/g/n standard and can therefore also be integrated into a wireless LAN network; both as a client or access point. With the server monitoring function, you can set the ALL3073v3 to monitor and reset a computer or router. A ping is sent to the registered system, if the system does not respond within a specified time, the output is switched off for an adjustable time.Examples of use: Remotely control and restart PCs and servers Restart routers remotely including automatic boot-up (dead time programmable) Time-controlled minimisation of unnecessary power consumption due to standby devices Complex switching scenarios in conjunction with other ALLNET building automation products including the influence of temperature, humidity, etc. Many other applications... Technical data: Network: 10BaseT 100BaseTX Network connection: RJ45 Supported standards: IEEE 802.3, IEEE 802.3u Protocols: HTTP/HTTPS TCP/IP Management/control: via web browser, XML, JSON Operating systems: All network-compatible operating systems Voltage range: 200 - 250 volts Switching current: max. 16 amps = 3680 ohmic load Current consumption: Idle mode: 1.5W ~2W WiFi active: 1 device connected and download approx. 1.80W ~ 2.70W How to use: Plastic housing with integrated earthing contact power socket/plug Environment: Temperature operation: 0 ~ 40 °C Humidity operating: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensing) Dimensions: 125 x 68 x 40 (60) mm (height x width x depth) Weight: 200 grams (adapter only) Labelling CE

Straight DC plug on the connection cable. Zm suitable for connection to many 12V devices that require up to 2A current. Standard plug 5.5mm / 2.1mm hollow plug. Input 100V-240V 50-60Hz 0,8A MAX Output 12V/2A

- compatible with ALL34xx/350x/4500/5000 - Measuring range -40...+125 °C, 0...100 %RH - resolution temperature 0,01 °C, resolution humidity: 0.01 % - Measuring accuracy Temp in whole range approx. +/- 0,6° (Typical: -20 + 90° = +/- = 0,2°) - Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1.5%) - With 1.5 m connection cable Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Highlights:   compatible with ALL3418v2/3419/35xx/4500/5000 Carbon dioxide sensor "CO2 sensor" displays the values in ppm. Aluminium housing with bracket for wall mounting CO2 measuring range 0-40000ppm Measurement accuracy ± (30 ppm + 3% MV) / (25 °C, 400 - 10'000 ppm) Connections: 1x RJ45 input / 1x RJ45 output (no longer compatible with ALL3000/400x & ALL4504/4404 8 Port Multiplexer) ALL4471 - Sensor Module for HVAC and Indoor Air Quality Applications ALLNET Technology for IR detection enables highly accurate carbon dioxide measurement at a competitive price. Along with the NDIR measurement technology for CO2 detection. Thanks to the dual-channel principle for the measurement of carbon dioxide concentration, the sensor compensates for long-term drifts automatically by design. The very small module height allows easy integration into different applications. Carbon dioxide is a key indicator of indoor air quality. Thanks to new energy standards and better insulation, houses have be-come increasingly energy efficient, but the air quality can deteriorate rapidly. Active ventilation is needed to maintain a comfortable and healthy indoor environment, and to improve the well-being and productivity of the inhabitants. ALLNET´s ALL4471 offers accurate and stable CO2. This enables customers to develop new solutions that increase energy efficiency and simultaneously support well-being.   Technical Details: CO2 Sensor Specifications CO2 measurement range 0 - 40'000 ppm Accuracy ± (30 ppm + 3% MV) (25 °C, 400 - 10'000 ppm) Repeatability 10 ppm Temperature stability 2.5 ppm / °C (0-50 °C) Response time (t63) 20 s Humidity Sensor Specifications Relative humidity measurement range 0 - 100 % RH Typ accuracy ±3% RH (0-100% RH) Repeatability 0.1% RH Response time (t63) 8 s Electrical Specifications Supply voltage 3.3 - 5.5 V Average current  @ 2s measurement rate 19 mA Max. current 75 mA

Highlights: compatible with ALL34xx/35xx/4500/5000 Particulate matter sensor shows the values in µg/m3, particles per cubic cm  Aluminium housing with bracket for wall mounting Fine dust measuring range 1 to 1000 µg/m3 Measurement accuracy ±10 µg/m3 @ 0 to 100 µg/m3 / ±10 % @ 100 to 1000 µg/m3 Connections: 1x RJ45 input / 1x RJ45 output (no longer compatible with ALL3000/400x & ALL4504/4404 8 Port Multiplexer) Particulate Matter Sensor ALL4472 For HVAC and Air Quality Applications With this new particulate matter sensor, ALLNET expands its range of environmental sensing solutions and opens up a new dimension in indoor and outdoor air quality applications. The ALL4472 particulate matter (PM) sensor represents a new technological breakthrough in optical PM sensors. Its measurement principle is based on laser scattering and makes use of ALLNET's innovative contamination-resistance technology. This technology, together with high-quality and long-lasting components, enables accurate measurements from the device's first operation and throughout its lifetime of more than eight years. PM2.5 and PM10 refer to particulate matter with particle diameter up to 2.5 microns and 10 microns, respectively, and are among the most dangerous air pollutants. Due to their small size, PM2.5 particles can travel deep into the human lung and cause a variety of health issues; for instance, by triggering asthma attacks or contributing to cardiovascular disease. The ALL4472 will enable the implementation of innovative air quality monitoring devices that prevent air pollution damage.  Technical Details: Particulate Matter Sensor Specifications Mass concentration accuracy1 ±10 μg/m3 @ 0 to 100 μg/m3 ±10 % @ 100 to 1000 μg/m3 Mass concentration range 1 to 1000 μg/m3 Mass concentration resolution 1 μg/m3 Particle detection size range2 Mass concentration:   PM1.0, PM2.5, PM4 and PM10 Number concentration:  PM0.5, PM1.0, PM2.5, PM4 and PM10 Lower limit of detection 0.3 μm Minimum sampling interval 1 sec (continuous mode) Lifetime > 8 years operating continuously 24h/day Dimensions 40.6 x 40.6 x 12.2 mm3 Operating temperature range -10 to +60 °C Storage temperature range -40 to +70 °C Electrical Specifications Interface UART, I2C, RJ45 "ALLNET" Supply voltage 4.5 – 5.5 V Average supply current @ 1 Hz measurement rate < 60 mA 1 Specified for PM2.5 at 25 °C using potassium chloride salt particles and the TSI DustTrakTM DRX Aerosol Monitor 8533 as a reference. 2 PMx defines particles with a size smaller than "x" micrometers (e.g., PM2.5 = particles smaller than 2.5 μm).

Gigabit non-isolated PD PoE splitter can support IEEE802.3af/at standard, compatible with 12/36 &45/78 dual mode power supply. input voltage: 44-57VDC, output voltage: 5V or 12VDC, and maximum full load power is 24W. Hightlights: Gigabit rate self-adaption, 8P copper cable RJ45 port. Support IEEE802.3af/at standard, Both mid-span ( 4/5+, 7/8- ) and end-span ( 1/2+, 3/6- ) Output voltage 5V/12VDC optional, suitable for various network terminals Input voltage 44-57VDC, rated output power 12W, greater than 82% efficiency Short circuit, over-current and over-temperature protection 2000V high voltage isolation (input stage to output stage), less than 200mV output ripple Incl. approx. 10cm long hollow plug cable on hollow plug outside= 5,5mm & inside 2,1mm for direct connection to terminals with hollow plug socket ALL-PS102G-AF-AT is a gigabit PD PoE splitter independently developed by ALLNET. It has a 1*RJ45 input port, 1*RJ45 output port, and 1*DC 5,5mm / 2,1mm socket. Its DC5V/12V output voltage selection switch is to meet the use of various non-PoE network terminals to connect to PoE switches. Effectively solving security monitoring, wireless networks, Limited by the power line layout, reduced system wiring, improved system stability and safety, and reduced maintenance costs. ALL-PS102G-AF-AT PoE splitter adopts ABS and PC flame-retardant plastic material. It complies with IEEE802.3 af/at PoE standard, end-span (1,2+, 3,6-), and mid-span (4,5+, 7,8-) two power supply modes. The output power is up to 24W. Low ripple, >82% efficiency, 2KV port protection isolation. It has short-circuit, over-current, over-temperature protection. Plug and play, no configuration, easy to use. Technical Details: Model ALL-PS102G-AF-AT Interface Characteristics Fixed Port 2*10/100/1000Base-T RJ45 ports (Data) 1*DC5521 power socket(Power) Ethernet Port Ethernet port can support 10/100/1000Base-T auto-sensing, full/half duplex MDI/MDI-X self-adaption Network Characteristics Transmission Bandwidth (Rate) 10/100/1000Mbps Twisted Pair Transmission 10BASE-T: Cat3,4,5 UTP(≤100 meter) 100BASE-TX: Cat5 or later UTP(≤100 meter) 1000BASE-T:Cat5e or later UTP(≤100 meter) Output VoltageSwitch 12V: DC12Voutput voltage (default) 5V: DC5Voutput voltage Network Protocol and Indicator Network Protocol IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T IEEE802.3x LED Indicator PoE indicator: POE (green), Power indicator: PWR (green) PoE & Power Supply PoE Port (PD) PD port IEEE802.3af/at @ POE   IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3x Power Supply Pin 1/2 (+), 3/6 (-),& 4/5 (+), 7/8 (-) Input Voltage 44-57VDC Output Voltage Default 12VDC ±0.5V, optional 5VDC ±0.5V Power Consumption Standby<1W, Full Load<24W Conversion Efficiency (Output: Input) ≥82% Physical Parameter Operation TEMP / Humidity -20~+55°C, 5%~90% RH Non condensing Storage TEMP / Humidity -40~+85°C, 5%~95% RH Non condensing Dimension (L*W*H) 103*50*29mm Net /Gross Weight <0.08kg /<0.1kg Lightning protection / protection level Lightning protection: 4KV 8/20us; Protection level: IP30 Marks CE