ALLNET Netzwerk NTP GPS Server ALL-NTP-101

Gigabit non-isolated PD PoE splitter can support IEEE802.3af/at standard, compatible with 12/36 &45/78 dual mode power supply. input voltage: 44-57VDC, output voltage: 5V or 12VDC, and maximum full load power is 24W. Hightlights: Gigabit rate self-adaption, 8P copper cable RJ45 port. Support IEEE802.3af/at standard, Both mid-span ( 4/5+, 7/8- ) and end-span ( 1/2+, 3/6- ) Output voltage 5V/12VDC optional, suitable for various network terminals Input voltage 44-57VDC, rated output power 12W, greater than 82% efficiency Short circuit, over-current and over-temperature protection 2000V high voltage isolation (input stage to output stage), less than 200mV output ripple Incl. approx. 10cm long hollow plug cable on hollow plug outside= 5,5mm & inside 2,1mm for direct connection to terminals with hollow plug socket ALL-PS102G-AF-AT is a gigabit PD PoE splitter independently developed by ALLNET. It has a 1*RJ45 input port, 1*RJ45 output port, and 1*DC 5,5mm / 2,1mm socket. Its DC5V/12V output voltage selection switch is to meet the use of various non-PoE network terminals to connect to PoE switches. Effectively solving security monitoring, wireless networks, Limited by the power line layout, reduced system wiring, improved system stability and safety, and reduced maintenance costs. ALL-PS102G-AF-AT PoE splitter adopts ABS and PC flame-retardant plastic material. It complies with IEEE802.3 af/at PoE standard, end-span (1,2+, 3,6-), and mid-span (4,5+, 7,8-) two power supply modes. The output power is up to 24W. Low ripple, >82% efficiency, 2KV port protection isolation. It has short-circuit, over-current, over-temperature protection. Plug and play, no configuration, easy to use. Technical Details: Model ALL-PS102G-AF-AT Interface Characteristics Fixed Port 2*10/100/1000Base-T RJ45 ports (Data) 1*DC5521 power socket(Power) Ethernet Port Ethernet port can support 10/100/1000Base-T auto-sensing, full/half duplex MDI/MDI-X self-adaption Network Characteristics Transmission Bandwidth (Rate) 10/100/1000Mbps Twisted Pair Transmission 10BASE-T: Cat3,4,5 UTP(≤100 meter) 100BASE-TX: Cat5 or later UTP(≤100 meter) 1000BASE-T:Cat5e or later UTP(≤100 meter) Output VoltageSwitch 12V: DC12Voutput voltage (default) 5V: DC5Voutput voltage Network Protocol and Indicator Network Protocol IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T IEEE802.3x LED Indicator PoE indicator: POE (green), Power indicator: PWR (green) PoE & Power Supply PoE Port (PD) PD port IEEE802.3af/at @ POE   IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3x Power Supply Pin 1/2 (+), 3/6 (-),& 4/5 (+), 7/8 (-) Input Voltage 44-57VDC Output Voltage Default 12VDC ±0.5V, optional 5VDC ±0.5V Power Consumption Standby<1W, Full Load<24W Conversion Efficiency (Output: Input) ≥82% Physical Parameter Operation TEMP / Humidity -20~+55°C, 5%~90% RH Non condensing Storage TEMP / Humidity -40~+85°C, 5%~95% RH Non condensing Dimension (L*W*H) 103*50*29mm Net /Gross Weight <0.08kg /<0.1kg Lightning protection / protection level Lightning protection: 4KV 8/20us; Protection level: IP30 Marks CE

ALLNET PoE Injector Gigabit PoE & PoE+ (15,4W/30W) / plastic housing / "ALL0488v6   Highlights: PoE injector according to IEEE802.3af/at with max. power of 30W 2x RJ45 Gigabit Ports PoE Output 55VDC@30W Midspan PoE PIN's 4/5 (+) and 7/8(-) internal power supply unit compact design incl. 1.5m power cable with IEC-C5 to IEC-CEE7 protective contact cable NEW: Wall mounting capable Intelligent power supply via network without switch With the ALLNET ALL0488V6 Power over Ethernet Injector you can install your PoE-enabled IP devices such as WLAN access points, VoIP phones and much more absolutely independent of existing power sockets. For example, WLAN access points can be installed in the most ideal locations in a building without having to worry about power cabling. Switches that are not PoE-capable can be "retrofitted" with Power over Ethernet at a reasonable price, especially if only a few ports with PoE supply are required. Here, the ALL0488V6 saves the purchase of a PoE switch. The ALLNET ALL0488V6 supports the IEEE802.3af & IEEE802.3at standard with a maximum power of 30W Watt. The ALL0488V6 does not need to be configured. It has an RJ45 input socket and an RJ-45 output socket, which is used to connect the switch and terminal device to the PoE injector. The cable length here can be up to 100 meters between switch and terminal device in total, as is usual in Ethernet. Due to its compact design, the ALLNET ALL0488V6 can be installed very easy. It has an internal power supply and supplies the PoE voltage on pins 4/5 (+) and 7/8 (-). Technical Details: Element Specifikation Standards: IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-Tx Fast Ethernet IEEE802.3ab 1000Base-T Gigabit Ethernet Support terminal equipment with IEEE802.3af/at, PoE++ RoHS Compliance WEEE Compliance Ethernet Ports: 1x RJ45 10/100/1000 Mbps for connection to switch or hub 1x RJ45 10/100/1000 for connection to PoE end device PoE Output: PoE IEEE802.11af/at, Power pins: 4/5(+) 7/8(-) Power supply: 100 - 240VAC, internal power supply / Output: 55V/550mA incl. connection cable earth contact on IEC320-C5 "Kleeblat/Micky-Mouse" approx. 80cm length Power consumption: 30 Watt maximum with connected PoE end device AC Surge Protection: 1.0KV (5P/5N) L-N 1.2/50 (8/20) Tr/Th us 2.0KV (5P/5N) L-PE 1.2/50 (8/20) Tr/Th us N -PE Housing: Plastic housing Mounting: Wall-mounted Dimensions: length/width/height: 140 x 63 x 33 mm Environment: Operating Temperature: 0 ~ 40 °C Operating Humidity 10% ~ 90% (non-condensing) Storage Temperature: -20 ~ 90 °C Storage Humidity: 10% ~ 90% (non-condensing) EMI: FCC CFR47 Part 15 EN55024 EN55032 EMS: IEC61000-4-2(ESD) ± 6kV(contact), ±8kV(air) IEC61000-4-3(RS) 10V/m(80MHz~2GHz) IEC61000-4-4(EFT) Power Port: ±2kV; Data Port:±1kV IEC61000-4-5(Surge) Power Port:±1kV/DM, ±2kV/CM IEC61000-4-6(CS) 10V(150kHz~80MHz) Immunity: IEC60068-2-6(Vibration) IEC60068-2-27(Impact) IEC60068-2-32(Free Fall) Marks: CE; FCC

Temperature measurement via network easy made Highlights: detection of Temperature / Humidity / Gas / Smoke / Movement etc. via network Robust metal housing Brackets for attachment to wall Suitable for all operating systems 1x ALL3006 Temp-Sensor including Flexible/Multiple Installation of different ALLNET Bulding-Automation Units can be controlled in one Web-GUI with JSON API Optional Free-Software Modules like SNMP  / FTP Upload / POST_GET / Upload into PoE Clock/Counter / EnOcean / The ALLNET ALL3419 IP Thermometer/Automation-Building-Main-Unit is a flexible and economical solution for temperature measurement over a network. The very compact design makes it suitable for use in confined spaces. The rugged metal housing has tabs for mounting on walls and ceilings and protects against mechanical damage. The ALL3419 IP Thermometer/Automation-Building-Main-Unit is connected to a computer network via cable or WLAN and is accessible by an IP address. The measured values ??can be accessed via web browser on the device itself. No additional software is required for operation. Thus the ALL3419 is appropriate for all operating systems. The temperature is measured by the included I2C RJ45 temperature sensor ALL3006. Another internal onboard sensor shows the internal system temperature. With the optional ALL3018 temperature & humidity sensor can detect also humidity. The measurement intervals can be set second by second. The last 512 values can be shown directly as a graphical trend. Additional Sensors and Actors can be also measure Gas / Movement etc. see http://www.allnet.de/en/allnet-brand/produkte/home-automation/home-automation-sensoren/ Intelligent features and programming by switching matrix Depending on measured values certain actions can be programmed over the software based switching matrix. For example, if temperature is above or below defined limits, the readings can be sent by email. This may once, several times, and/or in certain time intervals, so long as the matrix condition exists. Another possibility is switching of external IP switching devices, such as network-sockets series ALL307x or network-relay ALL4075/4175 as well as directly connected actuators, for example the relay module ALL4427/3527. Alternativly can be switches also over the JSON Protocol.   Flexible installation options The external sensors can be plugged directly on ALL3419 or can be connected remotely via a control line. For remote connection a simple network cable (RJ45 connector, Cat. 5) is suitable to connect the sensors with the CPU. This way of connection is used in all ALLNET Home Automation products. For this purpose, an existing cable network such as already installed network or telephone lines can be used. The maximum cable length between CPU and sensor module can be up to 100 meters. The power supply of the sensor modules is already done via the main unit. A separate power source for each sensor module is not necessary.   Borderless Cross-site temperature measurement Several ALL3419 can operate in conjunction with the bigger control and measurement computers ALLNET ALL3500/3505/4500 or ALL5000, to show a lot of geographically distributed values in a centralized way. Each individual ALL3419 is queried over an individual IP address and centrally stored and displayed in all the other Main-Units like ALL3418v2/3419/3500/3505/4500/5000 etc. Maximum number of sensors per ALL3419:       Element Specification Sensor interface: 3x RJ45 for sensor/actor modules 1x USB 2.0 for additional Wireless Dongles like "EnOcean or Plugwise" 1x RJ45 Console Port for Serial-Connection Ethernet: 1x RJ45 10/100Mbps Wireless LAN: Ralink/Mediatek MT7688AN 2,4 GHz Wireless N, up to 150 Mbps Security: WEP 64/128bit, WPA, WPA2 Standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Power source: 100~240 VAC, 50/60 Hz Power Consumption: <3 watt in operation Housing: metal housing Environment: Operating temperature: 0 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 70 °C Storage humidity: 5% ~ 90% (non-condensing) Regulatory: CE, RoHS Dimensions: 92 x 85 x 24 mm (L x W x H)  Weight: 134 g (ALL3419 with ALL3006 sensor) Package content: -ALLNET ALL3419 -ALLNET ALL3006 temperature sensor -WLAN antenna -External power supply -Quick installation guide

Your smart entry into building automation – ALLNET ALL3500v2 With the ALLNET ALL3500v2 building automation centre, you get a cost-effective and versatile platform that is optimally tailored to semi-professional requirements. Thanks to state-of-the-art technology, high connectivity and a wide range of applications, the ALL3500v2 is the perfect partner for your automation projects. Highlights at a glance: Cost-efficient platform: Maximum functionality with minimum space and cost requirements. Intuitive operation: Can be conveniently controlled via web interface (HTTP/HTTPS) or smartphone. Flexible data connection: Integration via JSON, MQTT or SNMP possible. Versatile sensor technology: Comprehensive monitoring of temperature, humidity, air pressure and more. Future-proof: Expandable with i2C sensor ports and compatible with a wide range of ALLNET sensors and actuators. Features that impress The ALL3500v2 is based on a stable embedded Linux platform (MIPS or ARM architecture), which enables seamless integration into existing systems. With four RJ45 ports for sensor modules, you can realise a wide range of control and monitoring tasks. Whether local control or cloud-based applications - the ALL3500v2 offers you all the tools you need to organise your building automation efficiently and securely. Versatile application options: HACCP temperature monitoring: Precise detection and control in critical environments. Room climate control: Monitoring of temperature and humidity for demand-based control of heaters or humidifiers. Security management: Detection of gas odour, smoke or water ingress and triggering of alarms. Automated garden irrigation: Time and humidity-controlled for maximum efficiency. Energy consumption optimisation: Control based on consumption data from external sensors (e.g. ALL4590/4490 power meter). Compact, powerful, versatile The ALL3500v2 combines a variety of functions in a compact design that has been specially developed for space-saving installations. With four relays, sensor ports and contact interfaces, it can be used flexibly and provides the basis for sophisticated automation solutions - ideal for private and commercial applications. Why ALLNET ALL3500v2? With the ALL3500v2 you get a reliable and economical solution for building automation. From monitoring and control to integration into complex installations, this central unit offers everything you need for smart, efficient and future-proof automation. Start your building automation now with the ALLNET ALL3500v2! Versatile sensors, actuators and switching options for your automation The ALLNET ALL3500v2 impresses with its flexibility and functionality: With four ports for external sensors and actuators, four relay outputs for controlling loads and four contact inputs for buttons or switches, it provides an ideal basis for complex automation applications. Sensing and control – Precise and versatile With the ALL3500v2, you can measure and analyse a variety of environmental parameters such as temperature, humidity or air pressure and execute automatic switching operations based on them. Control is either manual, time-controlled or dynamic, based on the measured values. Connectivity that inspires The ALL3500v2 is equipped with Ethernet and built-in WLAN, which enables easy integration into existing networks. Using an IP address in the TCP/IP network, you can: Retrieve and edit measurement data directly in the web browser. Receive automated notifications and reports by email. Request and control data via JSON or XML interfaces. Optional MQTT support enables the transmission of data to the cloud and integration into IoT environments. With its powerful connectivity and flexible control options, the ALL3500v2 is the perfect choice for efficient and future-proof building automation.   I²C-Bus – Intelligent use of existing cable networks The ALLNET ALL3500v2 enables an uncomplicated connection of measurement and control modules via a standard network cable (RJ45, Cat. 5). This allows you to continue using existing cable infrastructures such as network or telephone cabling and saves costs and effort during installation. Advantages of the I²C bus system: Simple cabling: A standard network cable is sufficient to connect sensors and modules. Long range: Up to 100 metres of cable between the central unit and module. Integrated power supply: The modules are supplied with power directly from the central unit – no separate power source required. USB port – external memory connection The USB port on the ALLNET ALL3500v2 allows you to integrate external storage media easily and flexibly. This allows data to be saved and processed directly on connected USB devices. This enables extended data logging and analysis. Maximum number of sensors per ALL3500v2: Technical data: Element Specification Interfaces: 4x RJ45 for sensor modules Network connection: 1x RJ45 10/100Mbps Switching relay: 4x potential-free Contact input: 4x for push-buttons, switches, etc. Wireless LAN: Mediatek MTK7688 SOC chipset 2.4 GHz Wireless N Security: WEP 64/128bit, WPA, WPA2 Supported standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Other interfaces: 1x USB 2.0 1x console Power supply: 100~240 VAC, 50/60 Hz, external power supply Power consumption: <5 watts maximum How to use: Metal walkway Environment: Operating temperature: 0 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Labelling: CE, RoHS Dimensions: 220.4 x 80 x 30 mm (length x width x height) Weight: 400 grams (device incl. WLAN antenna and ALL3006 sensor) Packaging contents: -ALLNET ALL3500v2 -ALLNET ALL3008 temperature sensor -WLAN antenna -External power supply -Operating instructions

Highlights: 10/100 Mbit RJ45 network connection  Wireless LAN according to IEEE802.11b/g/n with 150 Mbps  German protective contact sockets "Type F"  for 200 - 250 V alternating voltage  switching time and program controlled or manual possible  optional: recording of temperature/humidity  integrated current measuring module for consumption or feeding. The ALL4176v3 IP power strip can be used to switch electrical devices on and off via a computer network. It is integrated into a computer network, receives a unique IP address. Configuration and operation is performed independently of a particular platform or operating system via any web browser from a PC, MAC, webpad or smartphone. No additional software is required. Each individual socket can be switched manually and program-controlled via the web interface. The programming takes into account, among other things, time, week and calendar days, duration, pulse switching and much more. In addition, each individual socket can be switched manually by pushbutton on the device. Several ALL4176v3 can be operated interdependently in a network. Furthermore, they work together with other ALLNET automation solutions, such as ALL369x Powermeter, ALL3419, ALL4500, ALL5000, etc.. With optionally available sensors for temperature and humidity measurement, the application possibilities of the ALL4176v3 IP power strip expand enormously. The ALL4176v3 power strip also has an integrated current measurement module which can measure the consumption / supply of the entire power strip. It can measure volts / Hz / amps / watts as well as cos. Factor can be measured. Of course, everything can also be written about time control up to the recording of the data. Examples of use:     Targeted control and reboot of PCs and servers remotely     Restart of routers remotely     Time-controlled elimination of unnecessary power consumption by standby devices     Complex switching scenarios in connection with other ALLNET building automation products incl. influence of temperature, humidity, etc.     many other applications... Technische Daten: Connections: 6x safety socket 1x RJ45 LAN 10/100 Mbit/s 1x R-SMA (WLAN) 1x USB 2.0 host 1x USB-B socket (PowerON sensor) 1x RJ45 sensor connector (temp./humidity) WiFi: 2,4 GHz Wireless N, up to 150 Mbps WiFi Security: WEP/WPA/WPA2 Supported standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Protocols: HTTP/HTTPS TCP/IP Management/Control: Via web browser, XML operating systems: all network-compatible operating systems Voltage range: 200 - 250 volts Switching current: 6x 10 amps max. housing: Aluminum profile housing Environment: Temperature operation: 0 ~ 40 °C Humidity operation: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Dimensions: 425 x 140 x 55 (60) mm (length x width x height) Weight:    2470 grams (without packaging and accessories) Scope of delivery: 1 piece ALL4176v3 1 power cable devices 1 manual 1 WiFI antenna

Highlights: Intelligent 4-fold relay box for switching loads of up to 10 amps Operation via web browser (no software required) / XML and JSON Access via 100BaseTX Ethernet and WLAN 802.11b/g/n max. 150Mbit/s Can be switched as a remote actuator for the ALL3500 etc. control centres Slim, robust aluminium housing The ALLNET ALL4175v2 4-fold network relay can be used to switch electrical devices via a computer network. Configuration and operation is independent of an operating system and can be carried out via any web browser from a PC, MAC, tablet or smartphone. No additional software is required. Four screw terminals (2-pole) are available for connecting the electrical loads to be switched. Each of these interfaces can be switched individually. The switching operations can be carried out manually or programmed to be time-controlled. In addition, it can be used as a remote switching actuator by the current ALLNET automation solutions, e.g. ALL369x Powermeter, ALL3418v2, ALL3419, ALL3500, ALL3505, ALL4500, ALL5000, etc.). "see ALLNET remote function" In addition to the wired network connection, the ALL4175v2 network relay has a wireless LAN interface (2.4 GHz IEEE802.11b/g/n) and can therefore be wirelessly integrated into an existing WLAN network. An ALL4175v2 can also be used as a WLAN access point and control other WLAN clients.Technical data: Tags: 4x relay contact (screw terminal) 1x RJ45 LAN 10/100 Mbit/s 1x R-SMA (WLAN) Wireless LAN: 2.4 GHz Wireless N, up to 150 Mbps 1T1R Encryption: WEP,WPA,WPA2 Wireless LAN chipset: Ralink RT7688 Supported standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Protocols: HTTP/HTTPS TCP/IP Management/control: via web browser Operating systems: All network-compatible operating systems Voltage range: 200 - 250 volts Switching current: 4x 10 amps max. How to use: Aluminium enclosure with wall mounting option Environment: Operating temperature: 0 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Dimensions: 105 x 78 x 29 mm (length x width x height) Weight: 175 grams (without packaging and accessories) Labelling: CE  

Power Source and Consumption monitoring accessible via LAN/WLAN Analyse Power Consumption and feed Sensors capture measured values ??over controlling and switching save electricity!   The Allnet ALL3692 is the consistent further development of the successful ALL369x Power Meter series, this time for D0 power meter with optical output. This concrete and calibrated readings are always recognized.   Instrument for monitoring and control of your current power consumption at several measuring points Via the Internet from anywhere accessible (Internet connection at the location of ALL3692 required) Easy operation and installation through Web interface and the D0 OKK optical read head ALL3688, alternatively ALL3689 (no interference with the house wiring necessary) integrated web server Email alerting at a set value is exceeded 4 x D0 ports allows you to connect with each D0 power meter with optical output (ALL3688/ALL3689) Extensive consumption display with live chart, chart function, table display, etc. Possibility to download the readings in database format, eg as a CSV file Interfaces: 1 x network, 1x 300Mbit Wireless, D0 4x, 2x I2C sensor / port, 2x External USB ports    Easy installation by placing the OKK optical D0 read head with its magnetic ring on one of the supported meters listed in the compatibility list (Attention! Not listed meters could be made compatible by a software adaptation. It is not necessary to calibrate the ALL3692 using the D0 signals of the calibrated electricity meter. No intervention in the 230V house wiring is necessary.   Features und web interface: The "Speedometer??" Display of our power meter allows you to check live, what you up to date on current consumption each phase and also shows you the recognized current cost of consumption.   The additional sensor ports, you can optionally measured values ??such as Temperature, air pressure, brightness and to define optionally actuators.       The power meter allows you to graphically represent your consumption. You can represent a daily, weekly, monthly or yearly graphs and single-phase or hide. The configuration page of the Power Meter gives you the opportunity to set individual values ??within the device. This includes the cost of power consumption, labels and graph colors.   If you want to reuse or export for archiving the determined values ??of the power meter, you can export it easily via the web menu as CSV or SQL Lite file. The live charts of the device you graphically represents the current power consumption of the device. Here you have the possibility to compare directly single-phase power lines.   Technical Details:   Item Specification Interfaces:   4x D0 for D0-compatible power meter with optical output 2x RJ 45 Ports for sensor and/or actuator 2x USB for external use 1x RS232 System console port Internal Memory: 4GB USB Flash memory stick Network Interface: 1x RJ45 10/100Mbps 1x 2,4 GHz Wireless N, up to300 Mbps network protocols: HTTP/HTTPS, TCP/IP, SNTP, SMTP, SSH operating Systems: all network-capable operating system with a browser Power input: 100~240 V AC, 50/60 Hz, external Power Supply Power consumption: <3 watt (without additional modules, sensors and actuators) Case: Aluminum case with mounting bracket for wall mounting Environment: Temperature operating: 5 ~ 40 °C Humidity operating: 10% ~ 85% (non-condensing) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 95% (non-condensing) Certificates: CE, RoHS Dimension: 155 x 28 x 26 mm (Lenght x Width x Height) Weight: 260 grams (only device) Warranty: 36 months Package content: 1x ALL3692 1x ALL3688 OKK optical D0 readhead 1x Readhead-connection cable 2x WLAN Antennas 1x Ethernetcable 1x Power supply 230VAC - 12V DC 2A 2x universal brackets 1x manual

Know what's going on! Find power guzzlers! Analyzing power consumption! Save electricity! Highlight: Meter to measure and control your current power consumption Direct connection of the current phases up to 32A per phase. Current measurement via integrated shunts Can be accessed anywhere via the Internet (Internet connection at the ALL3967 location is required) Simple operation and installation through web interface Integrated web server Alerting by email when a preset value is exceeded 1x I2C port for additional sensors/actuators of the ALLNET MSR measurement control rules series Comprehensive consumption display with live diagram, chart function, table display, etc. Possibility to download the measured values in database format, e. g. as CSV file Interfaces: 1x network, 1x USB, 1x I2C, Connection of the 3 phases L1/L2/L3/N  Features and WebGUI: The power meter offers you the possibility to graphically display your consumption. You can display a daily, weekly, monthly or annual graph and show or hide individual phases. The configuration page of the power meter allows you to set individual values within the device. Example: Labels and graph colours. If you want to continue using the determined values of the power meter or if you want to export them for archiving, you can easily download them as a CSV file via the web menu. Of course, there is also the chance to call up the values live via JSON. Technische Daten:   Interfaces: 1x Direct Phase Contacts (L1/L2/L3/N) max. 32A 1x I2C Port for additional sensors & actors of ALLNET Building Automation products http://www.allnet.de/en/allnet-brand/produkte/building-automation/automation-steuer-computer/building-automation-sensors/ 1x USB 2.0 4x TTL Outputs 4x Open Collector Output 1x Console RS232 1x OLED-Display 1x LAN 10/100Mbps 1x WIFI 1T1R 150Mpbs Network Connector: 1x RJ45 10/100Mbps Power supply: 100~240 VAC, 50/60 Hz, internes PSU Consumption: <5 Watt maximal Housing: DIN-Rail housing 12TE subunits Environment: Temperature operation: 0 ~ 40 °C Operating Humidity: 10% ~ 85% (non-condensing) Temperature Storage: -20 ~ 60 °C Humidity Storage: 5% ~ 90% (non-condensing) Dimensions: 160 x 91 x 63 mm (length x width x height) Weight: 370 grams (without packaging and accessories) Marks: CE, RoHS Package contents: 1 piece ALLNET ALL3697 QIG Manual 1 Patchcable 1m    

Know what's happening Reacheable via Wifi  Analysing power consumption and supply Measurement value logging with sensors Controlling and shifting Save elictricity   The ALLNET ALL3696 is the evolution result of the successful ALL369x powermeter series. This time for power meters with optical D0 interface. This helps to receive concrete and calibratted measurement values.    Measurement device for capturing and control of your power consumption with several measurement points Reachable everywhere via internet ( internet connection at the location of ALL3696 is needed)  Easy handling and installation via web interface and the optical reading head ALL3688, alternatively ALL3689  Integrated web server Alarm via E-mail if adjusted values are exceeded 4x D0 ports enables the connection with every D0 power meter with optical output (ALL3688/ALL3689)  Extensive consumption displaying with live diagram, chart function, table display Possibility to download the measurement values e.g. as a CSV data Interfaces: 1x network, 1x 300Mbit Wifi, 4x D0, 2x I2C sensor/ports, 2x external USB connections      Technische Daten: Element Spezifikation Interfaces:   2x magnetic connections for inductive transducers 1x50A (included), optional 50A / 200A und 800A available  1x D0 for power meters with optical output compatibility list 1x S0 contact with pulse counter 1x console port Internal data memory:  4GB USB flash memory stick Network connections: 1x RJ45 10/100Mbps 1x 2,4 GHz Wireless N, up to 150 Mbps Network protocols: HTTP/HTTPS, TCP/IP, SNTP, SMTP, SSH Operating systems: all network-compatible operation systems with browser Power supply: 100~240 VAC, 50/60 Hz, external 12V 1A power supply Power consumption: <3 watt maximum Housing: Aluminum housing, possibility of wall mounting Environment: Temperature range: 0 ~ 40 °C Humidity operation: 10% ~ 85% (not condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (not condensed) Labels: CE, RoHS Dimensions: 155 x 28 x 26 mm (lenghtx width x height)  Weight: 260 gramms (without accessories and package) Package content: 1x ALL3696 1x 50A inductive transducers SET "L1/L2/L3" 1x Wifi antenna 1x Ethernet cables 1x power supply 230VAC - 12V DC 1A 2x universal mounting brackets 1x quick install guide

Straight DC plug on the connection cable. Zm suitable for connection to many 12V devices that require up to 2A current. Standard plug 5.5mm / 2.1mm hollow plug. Input 100V-240V 50-60Hz 0,8A MAX Output 12V/2A

DC Jack socket to plug Socket: 2.1 x 5.5mm Plug: 2.1 x 5.5mm Cable length: 95mm