ALLNET ALL3696 / Powermeter ALL3696 IP with 2x induction

Set of 3 induction terminals for the ALLNET ALL3690/ALL3691 Power Meterfor currents up to 200 amps per phase for all three phases,Inner diameter of clamp = 20mmConnection cable with plug 180cm lengthCurrent terminals NEVER connect without load (ALL369x)  NOTE: Correction factor about 0.2 ~ 0.25 entered in the Power Meter!

Set of 3 induction terminals for the ALLNET ALL3690/3691 Power Meterfor currents up to 50 amps per phase for all three phasesInner diameter of clamp: 10mmCurrent terminals NEVER connect without load (ALL369x)

Set of 3 induction terminals for the ALLNET ALL3690/3691 Power MeterFor currents up to 800 amps per phase for all three phasesInner diameter of clamp = 30mmCurrent terminals NEVER connect without load (ALL369x)

D0 sensor for ALL3691 for removing the D0 signal to modern electricity meters. The D0 signal is usually every 2 seconds automatically sent from the electricity meter of the energy supplier in the infrared range. Since each type of construction D0 electricity meter has a different shape, the ALLNET D0 sensor is individually attached to the meter (e.g. with tape).

D0 sensor for ALL3691/3692/3696 to pick up the D0 signal on modern electricity meters. The D0 signal is usually sent automatically every 2 seconds from the utility's electricity meter in the infrared range. The OKK D0 reading head is fixed on the electricity meters with magnetic ring. ATTENTION: Works only in combination with an ALLNET power meter with D0 connection, e.g. ALL361/3692/3696 and the corresponding compatible power meter. Which electricity meter is compatible see data sheet.

Gigabit non-isolated PD PoE splitter can support IEEE802.3af/at standard, compatible with 12/36 &45/78 dual mode power supply. input voltage: 44-57VDC, output voltage: 5V or 12VDC, and maximum full load power is 24W. Hightlights: Gigabit rate self-adaption, 8P copper cable RJ45 port. Support IEEE802.3af/at standard, Both mid-span ( 4/5+, 7/8- ) and end-span ( 1/2+, 3/6- ) Output voltage 5V/12VDC optional, suitable for various network terminals Input voltage 44-57VDC, rated output power 12W, greater than 82% efficiency Short circuit, over-current and over-temperature protection 2000V high voltage isolation (input stage to output stage), less than 200mV output ripple Incl. approx. 10cm long hollow plug cable on hollow plug outside= 5,5mm & inside 2,1mm for direct connection to terminals with hollow plug socket ALL-PS102G-AF-AT is a gigabit PD PoE splitter independently developed by ALLNET. It has a 1*RJ45 input port, 1*RJ45 output port, and 1*DC 5,5mm / 2,1mm socket. Its DC5V/12V output voltage selection switch is to meet the use of various non-PoE network terminals to connect to PoE switches. Effectively solving security monitoring, wireless networks, Limited by the power line layout, reduced system wiring, improved system stability and safety, and reduced maintenance costs. ALL-PS102G-AF-AT PoE splitter adopts ABS and PC flame-retardant plastic material. It complies with IEEE802.3 af/at PoE standard, end-span (1,2+, 3,6-), and mid-span (4,5+, 7,8-) two power supply modes. The output power is up to 24W. Low ripple, >82% efficiency, 2KV port protection isolation. It has short-circuit, over-current, over-temperature protection. Plug and play, no configuration, easy to use. Technical Details: Model ALL-PS102G-AF-AT Interface Characteristics Fixed Port 2*10/100/1000Base-T RJ45 ports (Data) 1*DC5521 power socket(Power) Ethernet Port Ethernet port can support 10/100/1000Base-T auto-sensing, full/half duplex MDI/MDI-X self-adaption Network Characteristics Transmission Bandwidth (Rate) 10/100/1000Mbps Twisted Pair Transmission 10BASE-T: Cat3,4,5 UTP(≤100 meter) 100BASE-TX: Cat5 or later UTP(≤100 meter) 1000BASE-T:Cat5e or later UTP(≤100 meter) Output VoltageSwitch 12V: DC12Voutput voltage (default) 5V: DC5Voutput voltage Network Protocol and Indicator Network Protocol IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T IEEE802.3x LED Indicator PoE indicator: POE (green), Power indicator: PWR (green) PoE & Power Supply PoE Port (PD) PD port IEEE802.3af/at @ POE   IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3x Power Supply Pin 1/2 (+), 3/6 (-),& 4/5 (+), 7/8 (-) Input Voltage 44-57VDC Output Voltage Default 12VDC ±0.5V, optional 5VDC ±0.5V Power Consumption Standby<1W, Full Load<24W Conversion Efficiency (Output: Input) ≥82% Physical Parameter Operation TEMP / Humidity -20~+55°C, 5%~90% RH Non condensing Storage TEMP / Humidity -40~+85°C, 5%~95% RH Non condensing Dimension (L*W*H) 103*50*29mm Net /Gross Weight <0.08kg /<0.1kg Lightning protection / protection level Lightning protection: 4KV 8/20us; Protection level: IP30 Marks CE