ALLNET MSR control center “ALL3500v2” incl. 4 sensor ports & WLAN for IP building automation

Gigabit non-isolated PD PoE splitter can support IEEE802.3af/at standard, compatible with 12/36 &45/78 dual mode power supply. input voltage: 44-57VDC, output voltage: 5V or 12VDC, and maximum full load power is 24W. Hightlights: Gigabit rate self-adaption, 8P copper cable RJ45 port. Support IEEE802.3af/at standard, Both mid-span ( 4/5+, 7/8- ) and end-span ( 1/2+, 3/6- ) Output voltage 5V/12VDC optional, suitable for various network terminals Input voltage 44-57VDC, rated output power 12W, greater than 82% efficiency Short circuit, over-current and over-temperature protection 2000V high voltage isolation (input stage to output stage), less than 200mV output ripple Incl. approx. 10cm long hollow plug cable on hollow plug outside= 5,5mm & inside 2,1mm for direct connection to terminals with hollow plug socket ALL-PS102G-AF-AT is a gigabit PD PoE splitter independently developed by ALLNET. It has a 1*RJ45 input port, 1*RJ45 output port, and 1*DC 5,5mm / 2,1mm socket. Its DC5V/12V output voltage selection switch is to meet the use of various non-PoE network terminals to connect to PoE switches. Effectively solving security monitoring, wireless networks, Limited by the power line layout, reduced system wiring, improved system stability and safety, and reduced maintenance costs. ALL-PS102G-AF-AT PoE splitter adopts ABS and PC flame-retardant plastic material. It complies with IEEE802.3 af/at PoE standard, end-span (1,2+, 3,6-), and mid-span (4,5+, 7,8-) two power supply modes. The output power is up to 24W. Low ripple, >82% efficiency, 2KV port protection isolation. It has short-circuit, over-current, over-temperature protection. Plug and play, no configuration, easy to use. Technical Details: Model ALL-PS102G-AF-AT Interface Characteristics Fixed Port 2*10/100/1000Base-T RJ45 ports (Data) 1*DC5521 power socket(Power) Ethernet Port Ethernet port can support 10/100/1000Base-T auto-sensing, full/half duplex MDI/MDI-X self-adaption Network Characteristics Transmission Bandwidth (Rate) 10/100/1000Mbps Twisted Pair Transmission 10BASE-T: Cat3,4,5 UTP(≤100 meter) 100BASE-TX: Cat5 or later UTP(≤100 meter) 1000BASE-T:Cat5e or later UTP(≤100 meter) Output VoltageSwitch 12V: DC12Voutput voltage (default) 5V: DC5Voutput voltage Network Protocol and Indicator Network Protocol IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3ab 1000Base-T IEEE802.3x LED Indicator PoE indicator: POE (green), Power indicator: PWR (green) PoE & Power Supply PoE Port (PD) PD port IEEE802.3af/at @ POE   IEEE802.3 10BASE-T, IEEE802.3i 10Base-T IEEE802.3u 100Base-TX, IEEE802.3x Power Supply Pin 1/2 (+), 3/6 (-),& 4/5 (+), 7/8 (-) Input Voltage 44-57VDC Output Voltage Default 12VDC ±0.5V, optional 5VDC ±0.5V Power Consumption Standby<1W, Full Load<24W Conversion Efficiency (Output: Input) ≥82% Physical Parameter Operation TEMP / Humidity -20~+55°C, 5%~90% RH Non condensing Storage TEMP / Humidity -40~+85°C, 5%~95% RH Non condensing Dimension (L*W*H) 103*50*29mm Net /Gross Weight <0.08kg /<0.1kg Lightning protection / protection level Lightning protection: 4KV 8/20us; Protection level: IP30 Marks CE

The ALLNET NTP Server is a time server based on the NTP (V2, V3, V4) / SNTP protocol. It obtains standard UTC time information from the GNSS satellite receiver and transmits this information on the network. Devices that need time signals in the network, such as computers and controllers, can synchronize with the standard clock signal to realize the network timing function The standard clock signals are transmitted through the TCP/IP network and support point-to-point and broadcast transmission modes. The product is easy to operate. Just connect the GNSS satellite antenna and the whole network can synchronize the time. The product has small size and structure, convenient installation, extremely low power consumption and is plug and play. Technical data: Up to 6000 visits per second Webui interface, convenient and fast management LAN synchronous time accuracy: 0.5-2ms Internally integrated GNSS satellite receiver with high precision time measurement Supports GPS, Beidou, GLONASS and QZSS NTP v2 (RFC 1119),NTP v3 (RFC 1305),NTP v4 (RFC5905) SNTP v3 (RFC 1769), SNTP v4 (RFC 2030) Supports MD5 information verification Supports server and broadcast working modes; Ethernet port supports 10 / 100M, full duplex and half duplex and supports auto-negotiation mechanism Supports user-defined MAC addresses NMEA0183 is transmitted via TCP protocol Compact structure and convenient installation Power consumption is only 1W Industrial operating temperature range

isolated switching output for ALL3000/3500/400x/4500/5000optoelectroniccoupler, with max. 20 mA switching current

Temperature sensor compatible with ALL3000/34xx/3500/ALL400x/4500/5000 Measuring range -55 to +80 °C, 13-bit ADC with a temperature resolution of 0.03125 °C Temperature accuracy of ± 1 °C from -25 °C to +100 °C with 1 m connection cable Exclusively only one of the following sensors possible per sensor port! ALL4454, ALL4432, ALL4421, ALL4590, ALL4532, ALL4552, ALL4522, ALL3005-6, ALL3015,ALL4006, ALL4506-7  

Temperature sensor for ALL3000/34xx/3500/400x/4500/5000 WATERPROOF & salt water resistant Measuring range -55 to +125 °C Resolution 0.06°C 1m silicone cable with shrink cap with RJ45 Keystone socket "Art. 88971" The scope of delivery also includes 1x 20m patch cable.  

- compatible with ALL34xx/350x/4500/5000 - Measuring range -40...+125 °C, 0...100 %RH - resolution temperature 0,01 °C, resolution humidity: 0.01 % - Measuring accuracy Temp in whole range approx. +/- 0,6° (Typical: -20 + 90° = +/- = 0,2°) - Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1.5%) - With 1.5 m connection cable Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Threshold switch for vertical installation (pen with float-ring) made ??of polyamide, resistant to gasoline, oil, brake fluid and much more. 1 m connection cable for ALL3000/ALL4000

Compatible with ALL3000/34xx/3500/400x/4500/5000 Fluid threshold for horizontal installation (hinged float) made ??of polyamide, resistant against gasoline, oil, brake fluid, etc. With 1 m cable

Leakage Sensor for 3418v2/34xx/35xx/4500/5000 - Detects if leading conductive liquid is present on the floor - In the display / central unit, the display is shown in % percentage = Example: Ca. 95~100% floaters are in the water. 50% display = There is still some conductive liquid present on the floor. From 40% the threshold is pre-configured from green to red. - Connections: 2x RJ45 I2C at the sensor housing - Including 2m cable length to the floaters that register the conductivity of the liquid on the floor Example view in WebGUI: Sensor information: Installation example:

Compatible with ALL3000/34xx/3500/400x/4500/5000 passive infrared motion detector reliable motion detection extremely high noise immunity changeable lens is standard 90° NC tamper switch manual adjustment range (up to 15 x 15 m) creep with counter with 1 m cable

Temperature sensor DIN RAIL 27 mm compatible with ALL3000/34xx/3500/400x/4500/5000 temp range -40...+85 Grad C, 0,06 °C resolution

Compatible with ALL3000/34xx/3500/400x/4500/5000 isolated reed relay with 100 mA switched circuit 27 mm width DIN RAIL

Compatible with ALL3000/34xx/3500/400x/4500/5000 volt meter DIN RAIL, 27 mm width detect when power fit or not isolated by relay 1-phase for AC voltage 220...240V incl. 1 m cable

Compatible with ALL3000/34xx/3500/400x/4500/5000 DIN RAIL, 27 mm width with screwed or sticking piezo element to detect the vibrations sensitivity adjustable by potentiometer including 1 m cable

compatible with ALL3000/3418v2/3500/400x/4500/5000DIN RAIL, 27 mm widthdetect noise via included condenser sensivity microphonesensivity adjustable by potentiometerAlarm is stored for 10 seconds and then will be automatically deletedincluding 1m cable

compatible with ALL3000/3418v2/3500/400x/4500/5000detect when power fit or notisolated by relaismetal case with wallmount optionconnection: 1x RJ45 INPUT, 1x RJ45 OUTPUT, 2pin screw connection

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C   Temperature sensor in desktop-/ wallmounting case   measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Multiplexing module hub for star-shaped distribution of up to 8 sensor modules for ALL4500/ALL5000. For the operation of the ALL4404 a base station/central unit is required. With the ALL4404 you expand the possible sensors by a factor of 8. A maximum of 1x ALL4404 can be connected per master port on the central station. The maximum cable length from the I2C sensor port is max. 100m and is NOT extended by the ALL4404 i.e. the maximum cable length through the hub is still 100m. Application example:  ALL4404 (Single) ALL3419 ALL3500 ALL3505 ALL5000v2      

 Highlights:  new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4406 Temperature sensor has a measuring range of -40 to +85 ° C Temperature sensor in desktop-/ wallmounting case measuring range of -40 to +85 °C, resolution 0,06 °C Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type Temperature and relative humidity Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip: SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4418 Temperatore sensor 1x connection cable        Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights: new flat desktop / wall mount case made of aluminium I2C bus for multiplexing use measuring range -40...+125 °C, 0...100 %RH resolution temperature 0,01 °C, resolution humidity: 0.01 % Measuring accuracy Temp in whole range approx. +/- 0.6° (Typical: -20 + 90° = +/- = 0.2°) Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1,5%) ONLY COMPATIBLE WITH ALL34xx/350x/4500/5000 Angle brackets for wall mounting Measure, control and regulate automatically and independently ALLNET has been pursuing the concept of intelligent control of building technology processes via network and Internet for years. Intelligent building technology not only offers more comfort, but also actively promotes the saving of energy costs. Centrally controlled and accessible via network / Internet, ALLNET building automation products enable intelligent building technology independent of time and location.   Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Compatible with ALL3000/34xx/3500/400x/4500/5000 counter in metal case, wall mount option it counts how often the contact has been closed counter frequency: 1000 Impulses/Sec 6-digit counter (0...999999) with 1 m cable

• Compatible to ALL3000/34xx/3500/400x/4500/5000 • Contact counter in metal housing • Counts how often a contact has been closed. Max counting frequency: 1000 pulses/second • counter 6-digit decimal (0 … 999999) • 1 m cable

Highlights: Compatible with ALL34xx/3500/4500/5000 4-port relay output in metal desktop/wall-mounted housing switches 4 relays with ON contacts 250V/10A (no longer compatible with ALL3000/ALL4000) The ALL4427 is a powerful 4-port relay output in a robust aluminium housing that is ideal for controlling various electrical loads, whether for controlling lights, pumps or other devices with a maximum current requirement of up to 10 amps per relay. With a voltage of up to 250V per switching contact, the ALL4427 offers reliable performance for demanding applications. Compatibility and versatility: Compatible with models of the ALL34xx/3500/4500/5000 series, but no longer with ALL3000 or ALL4000. The connection is made via 2x RJ45 sockets, allowing the device to be easily integrated into existing networks. Handling and mounting: The aluminium housing is durable and resistant, ideal for harsh environments and use in demanding projects. The integrated wall mounting bracket enables simple and stable mounting on walls or in the control cabinet. Multiplexing for extended applications: Multiple multiplexing allows several modules to be operated simultaneously on one line, which enables flexible expansion of the relay control for more extensive setups. This 4-port relay module offers a reliable solution for controlling electrical devices and is an ideal choice for users looking for flexible application options and easy installation. Technical details: Element Specification Sensor type 4-fold relay with ON contacts 250V/10A Chip PCF8574 Connection: 2x RJ45 (I2C bus) Multiplexing: Adjustment wheel for ID LED indicators: 1x PWR, 1x BUS, 4x contact output How to use: Metal walking Environment: Temperature operation: -45 ~ 90 °C Humidity operating: 10% ~ 85% (non-condensing) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensing) Labelling: CE, RoHS Dimensions: 79 x 50 x 24 mm (length x width x height) Weight: 230 grams (without packaging and accessories) Packaging contents: 1x ALL4427 4-fold relay 1x 1m connection cable

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4429 Combination sensor has a measuring range of 0 to 1023 mbar, -40 to +80 °C and 0...100 % RH Combination Sensor of air pressure/humidity/temperature in desktop-/ wallmounting case measuring range of 0 to 1023 mbar / -40 to +80 °C (resolution 0,01 °C) / 0...100 % RH (resolution 0,5%) Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 not compactible with ALL3000/ALL5000 Technical Details: Item Specification Sensor type air pressure, humidity, temperature air pressure measuring range: 0 to 1023 mbar Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip BMP085 + SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4429 Combination sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.  

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting   Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4432 Brightness sensor indicates the brightness as value of 0 to 100.   Brightness Sensor in desktop-/ wallmounting case   measuring range of 0 to 100 Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Brightness analog 16bit measuring range: 0 to 100 Chip ADS1100A2 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4432 Brightness sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Compatible with ALL34xx/350x/4500/5000/3692 4-Port contact input in metal case with wall mount option  4Port contact input (isolated) result of open contacts is "1", closed contact is "0" - possible solutions: idle door contact with puls stretching NOT COMPATIBLE WITH ALL3000/ALL40000.

Compatible with ALL3000/ALL34xx/3500/400x/4500/5000 volt meter in metal case housing with wall mount/desktop option detect when power fit or not 4-phase, for AC voltage 220...240V isolated over relay connections: 1x RJ45 INPUT / 1x RJ45 OUTPUT

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4452 PIR Movement detector has a max. detection angle of 92° and a max range of 8 meters. Movement detection Sensor in desktop-/ wallmounting case max. detection angle of 92°, max. range of 8 meters Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type   PIR movement detection   measuring range: max. detection angle of 92°, max. range of 8 meters Chip PCF8574 Interfaces: 2x RJ45 (I2C Bus) Multiplexing:   dial wheel for ID (8), see note below   LED Indicators: 1x PWR, 1x BUS, 1x Detetct Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4452 PIR Movement detection sensor 1x connection cable   Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more thanone sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Hightlights: new compact aluminium desktop- / wall mounting case I2C Bus for multiplexing use either in black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4454 smoke detector/ sensor can also be used for detection of gases. Smoke detector/ Gas sensor in desktop-/ wallmounting case reports smoke and gas Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Smoke-/ Gas detector measuring range: 0 to 100 Chip ADS1100A3 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4454 smoke detector / Gas sensor 1x connection cable Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

  Highlights:   new compact aluminum desktop- / wall mounting case I2C Bus for multiplexing use either in black or white available angle fixings for wall mounting       Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4454 smoke detector/ sensor can also be used for detection of gases.     Smoke detector/ Gas sensor in desktop-/ wall mounting case   reports of smoke and gas Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x)   Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.     Technical Details:   Item Specification Sensor type Smoke-/ Gas detector measuring range: 0 to 100 Chip ADS1100A3 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non-condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4454 smoke detector / Gas sensor 1x connection cable

ALL4500_COM - RS232 Interface adapter cable 1x RJ45 to 3x DB9 connector.For ALL4500, ALL3500, ALL3691, ALL3692, ALL3693, ALL5002Eval, ALL5003Eval.DB9 connector occupancy: Pin 2: TX, Pin3: RX, Pin 5: GND.

Temperature sensor for ALL3000/34xx/35xx/400x/4076/4500/5000 in desktop/wall housing Interface for connection of PT1000 temperature sensors Aluminium housing with bracket for wall mounting Multiple multiplexing = several multiplexing modules on one line Connection: 1x RJ45 input, 1x RJ45 output

Temperature sensor for ALL34xx/35xx in desktop/wall housing Interface for the connection of PT100 temperature sensors Aluminum housing with bracket for wall mounting Multiple multiplexing = several multiplexing modules on one line Connection: 1x RJ45 input, 1x RJ45 output

Phoenix 2poliger Stecker für ALL3500 Relais-Ausgänge

Highlights: compatible with ALL34xx/35xx/4500/5000 Particulate matter sensor shows the values in µg/m3, particles per cubic cm  Aluminium housing with bracket for wall mounting Fine dust measuring range 1 to 1000 µg/m3 Measurement accuracy ±10 µg/m3 @ 0 to 100 µg/m3 / ±10 % @ 100 to 1000 µg/m3 Connections: 1x RJ45 input / 1x RJ45 output (no longer compatible with ALL3000/400x & ALL4504/4404 8 Port Multiplexer) Particulate Matter Sensor ALL4472 For HVAC and Air Quality Applications With this new particulate matter sensor, ALLNET expands its range of environmental sensing solutions and opens up a new dimension in indoor and outdoor air quality applications. The ALL4472 particulate matter (PM) sensor represents a new technological breakthrough in optical PM sensors. Its measurement principle is based on laser scattering and makes use of ALLNET's innovative contamination-resistance technology. This technology, together with high-quality and long-lasting components, enables accurate measurements from the device's first operation and throughout its lifetime of more than eight years. PM2.5 and PM10 refer to particulate matter with particle diameter up to 2.5 microns and 10 microns, respectively, and are among the most dangerous air pollutants. Due to their small size, PM2.5 particles can travel deep into the human lung and cause a variety of health issues; for instance, by triggering asthma attacks or contributing to cardiovascular disease. The ALL4472 will enable the implementation of innovative air quality monitoring devices that prevent air pollution damage.  Technical Details: Particulate Matter Sensor Specifications Mass concentration accuracy1 ±10 μg/m3 @ 0 to 100 μg/m3 ±10 % @ 100 to 1000 μg/m3 Mass concentration range 1 to 1000 μg/m3 Mass concentration resolution 1 μg/m3 Particle detection size range2 Mass concentration:   PM1.0, PM2.5, PM4 and PM10 Number concentration:  PM0.5, PM1.0, PM2.5, PM4 and PM10 Lower limit of detection 0.3 μm Minimum sampling interval 1 sec (continuous mode) Lifetime > 8 years operating continuously 24h/day Dimensions 40.6 x 40.6 x 12.2 mm3 Operating temperature range -10 to +60 °C Storage temperature range -40 to +70 °C Electrical Specifications Interface UART, I2C, RJ45 "ALLNET" Supply voltage 4.5 – 5.5 V Average supply current @ 1 Hz measurement rate < 60 mA 1 Specified for PM2.5 at 25 °C using potassium chloride salt particles and the TSI DustTrakTM DRX Aerosol Monitor 8533 as a reference. 2 PMx defines particles with a size smaller than "x" micrometers (e.g., PM2.5 = particles smaller than 2.5 μm).

Highlights:   compatible with ALL3418v2/3419/35xx/4500/5000 Carbon dioxide sensor "CO2 sensor" displays the values in ppm. Aluminium housing with bracket for wall mounting CO2 measuring range 0-40000ppm Measurement accuracy ± (30 ppm + 3% MV) / (25 °C, 400 - 10'000 ppm) Connections: 1x RJ45 input / 1x RJ45 output (no longer compatible with ALL3000/400x & ALL4504/4404 8 Port Multiplexer) ALL4471 - Sensor Module for HVAC and Indoor Air Quality Applications ALLNET Technology for IR detection enables highly accurate carbon dioxide measurement at a competitive price. Along with the NDIR measurement technology for CO2 detection. Thanks to the dual-channel principle for the measurement of carbon dioxide concentration, the sensor compensates for long-term drifts automatically by design. The very small module height allows easy integration into different applications. Carbon dioxide is a key indicator of indoor air quality. Thanks to new energy standards and better insulation, houses have be-come increasingly energy efficient, but the air quality can deteriorate rapidly. Active ventilation is needed to maintain a comfortable and healthy indoor environment, and to improve the well-being and productivity of the inhabitants. ALLNET´s ALL4471 offers accurate and stable CO2. This enables customers to develop new solutions that increase energy efficiency and simultaneously support well-being.   Technical Details: CO2 Sensor Specifications CO2 measurement range 0 - 40'000 ppm Accuracy ± (30 ppm + 3% MV) (25 °C, 400 - 10'000 ppm) Repeatability 10 ppm Temperature stability 2.5 ppm / °C (0-50 °C) Response time (t63) 20 s Humidity Sensor Specifications Relative humidity measurement range 0 - 100 % RH Typ accuracy ±3% RH (0-100% RH) Repeatability 0.1% RH Response time (t63) 8 s Electrical Specifications Supply voltage 3.3 - 5.5 V Average current  @ 2s measurement rate 19 mA Max. current 75 mA

The new central unit for your building control system Highlights: 16x I2C sensor ports for maximum expansion. max. 128x possible sensors via ALL4404 multiplexing hub. Linux based opensource operating system 1x USB front port for optional USB dongles Two-line LCD display for status and IP address indication Redundant 12VDC input with "Widget" display in Webgui   The ALLNET ALL5000v2 IP Facility Control Server is the new flagship of the ALLNET home automation series. It offers all the features of the other MSR control centers, which is the consistent further development of the popular ALLNET MSR Ethernet sensor meter. During the development of the control server, the wishes of existing MSR users were taken into account and a large number of new features and interfaces were added without sacrificing the familiar functions. Also new is the expandability of the devices. The ALLNET ALL5000v2 IP Facility Control Server automates all tasks in building control, such as detection and signaling of environmental conditions such as temperature, humidity, pressure and much more, as well as triggering switching operations via contacts, relays and the like. This can be done manually, time-controlled or depending on recorded values. A wide variety of scenarios such as lighting, blinds, ventilation and household appliances can be controlled with the ALLNET ALL5000v2 IP Facility Control Server. From temperature detection and demand-based heating of individual rooms, control of garden irrigation, alarming in case of gas smell and water intrusion to automatic opening and closing of blinds depending on daylight and much more, there are no limits to your ideas. Accessible everywhere via network, internet and smartphone You control everything from a PC, notebook or other mobile device, such as smartphone or webpad. No matter if the devices you want to control, measure, regulate are located in the same building or on another continent. The ALLNET ALL5000v2 is accessible via an IP address. Your existing computer network and the Internet serve as the medium. The determined values can be retrieved directly from the device via the web browser or sent periodically via email or when a value exceeds or falls below certain preset limits. An integrated JSON interface is used to retrieve data externally via the Internet.   Individually adapted to every need The ALLNET ALL5000v2 IP Facility Control Server has a Linux-based opensource operating system. Thus it offers enough freedom for own developments and adaptations of the software directly to the intended use of the user. Would you like a little more? The new interface diversity The ALLNET ALL5000v2 IP Facility Control Server leaves nothing to be desired and even tops the ALLNET ALL3505 Sensoric Appliance. There are 16 sensor ports (RJ45) for the connection of sensors, actuators, relays, etc. available. TThere is 1x USB port available, which can be used for example for USB memory sticks or EnOcean USB dongle for the use of EnOcean wireless switches. The two-line LCD display integrated into the housing shows you the status and the IP address. Technical Details: Element Specification Product: ALLNET ALL5000v2 IP Facility Control Server Module ports for measuring and switching modules: 16x RJ45 I2C-Sensor Ports for additional Sensors/Actors.    Interfaces: 1x USB 2.0 extern 1x USB 2.0 intern 1x Temperatursensor onboard Network connection: 1x RJ45 10/100Mbps Power Supply: 100~240 VAC, 50/60 Hz, internal power supply unit optional redundant 12VDC power input Power consumption: <3 Watt (without additional modules) Housing: 19" metal housing (1U) Environment: Temperature operation: 5 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Marks: CE, RoHS Dimensions: 440 x 230 x 44 mm (width x depth x height) Package contents: 1 piece ALLNET ALL5000v2 1 piece ALLNET ALL3008 temperature sensor 1 manual Power cable

- Mini stick-on contact with flange - Self-adhesive and screw mount - Max. Contact Resistance (OHM) = 0,2 - Max Rating Current (mA) = 500mA - Max. Switching Voltage (VDC) = 100VDC - 12 inch (30cm) side leads with AWG #24 - Magnet : NdFeB - Color : white - incl. 2 PIN-Phoenix Contact Connector for ALLNET MSR Series

Highlights: 10/100 Mbit RJ45 network connection  Wireless LAN according to IEEE802.11b/g/n with 150 Mbps  German protective contact sockets "Type F"  for 200 - 250 V alternating voltage  switching time and program controlled or manual possible  optional: recording of temperature/humidity  integrated current measuring module for consumption or feeding. The ALL4176v3 IP power strip can be used to switch electrical devices on and off via a computer network. It is integrated into a computer network, receives a unique IP address. Configuration and operation is performed independently of a particular platform or operating system via any web browser from a PC, MAC, webpad or smartphone. No additional software is required. Each individual socket can be switched manually and program-controlled via the web interface. The programming takes into account, among other things, time, week and calendar days, duration, pulse switching and much more. In addition, each individual socket can be switched manually by pushbutton on the device. Several ALL4176v3 can be operated interdependently in a network. Furthermore, they work together with other ALLNET automation solutions, such as ALL369x Powermeter, ALL3419, ALL4500, ALL5000, etc.. With optionally available sensors for temperature and humidity measurement, the application possibilities of the ALL4176v3 IP power strip expand enormously. The ALL4176v3 power strip also has an integrated current measurement module which can measure the consumption / supply of the entire power strip. It can measure volts / Hz / amps / watts as well as cos. Factor can be measured. Of course, everything can also be written about time control up to the recording of the data. Examples of use:     Targeted control and reboot of PCs and servers remotely     Restart of routers remotely     Time-controlled elimination of unnecessary power consumption by standby devices     Complex switching scenarios in connection with other ALLNET building automation products incl. influence of temperature, humidity, etc.     many other applications... Technische Daten: Connections: 6x safety socket 1x RJ45 LAN 10/100 Mbit/s 1x R-SMA (WLAN) 1x USB 2.0 host 1x USB-B socket (PowerON sensor) 1x RJ45 sensor connector (temp./humidity) WiFi: 2,4 GHz Wireless N, up to 150 Mbps WiFi Security: WEP/WPA/WPA2 Supported standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Protocols: HTTP/HTTPS TCP/IP Management/Control: Via web browser, XML operating systems: all network-compatible operating systems Voltage range: 200 - 250 volts Switching current: 6x 10 amps max. housing: Aluminum profile housing Environment: Temperature operation: 0 ~ 40 °C Humidity operation: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Dimensions: 425 x 140 x 55 (60) mm (length x width x height) Weight:    2470 grams (without packaging and accessories) Scope of delivery: 1 piece ALL4176v3 1 power cable devices 1 manual 1 WiFI antenna

Highlights: Enables switching of the connected load (up to 16A) via the integrated web server- New release 3.2 Wireless LAN according to IEEE802.11b/g/n with 300 Mbps & 10/100 Mbit RJ45 network connection German earthing contact plug/socket for 200 - 250 V alternating voltage Switching time, programme-controlled or manually possible The ALL3073v3 network socket can be used to switch electrical devices on and off via a computer network. The ALL3073v3 acts as an intermediate plug between the power socket and the electrical consumer. It is integrated into a computer network and receives a unique IP address. It can be configured and operated via any web browser from a PC, MAC, webpad or smartphone, regardless of a specific platform or operating system. No additional software is required. The switching operations can be programmed manually, time-controlled, etc. Several ALL3073v3s can be switched independently of each other. They also work together with other ALLNET automation solutions, such as ALL369x Powermeter, ALL3418v2, ALL3500, ALL3505, ALL4500 or ALL5000. The ALLNET ALL3073v3 adapter is also equipped with the heavily revised user interface 3.2. In addition to numerous innovations in the user interface, Release 3.2 also offers the option of quickly and easily integrating multiple ALLNET remote sensors and actuators into the control interface via JSON for the first time. This means that the sensor data can be managed across locations via a central interface, resulting in significantly greater clarity and simpler administration. In addition to the wired 10/100Mbit/s RJ45 network interface, the ALL3073v3 also has a wireless LAN interface in accordance with the IEEE802.1b/g/n standard and can therefore also be integrated into a wireless LAN network; both as a client or access point. With the server monitoring function, you can set the ALL3073v3 to monitor and reset a computer or router. A ping is sent to the registered system, if the system does not respond within a specified time, the output is switched off for an adjustable time.Examples of use: Remotely control and restart PCs and servers Restart routers remotely including automatic boot-up (dead time programmable) Time-controlled minimisation of unnecessary power consumption due to standby devices Complex switching scenarios in conjunction with other ALLNET building automation products including the influence of temperature, humidity, etc. Many other applications... Technical data: Network: 10BaseT 100BaseTX Network connection: RJ45 Supported standards: IEEE 802.3, IEEE 802.3u Protocols: HTTP/HTTPS TCP/IP Management/control: via web browser, XML, JSON Operating systems: All network-compatible operating systems Voltage range: 200 - 250 volts Switching current: max. 16 amps = 3680 ohmic load Current consumption: Idle mode: 1.5W ~2W WiFi active: 1 device connected and download approx. 1.80W ~ 2.70W How to use: Plastic housing with integrated earthing contact power socket/plug Environment: Temperature operation: 0 ~ 40 °C Humidity operating: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non-condensing) Dimensions: 125 x 68 x 40 (60) mm (height x width x depth) Weight: 200 grams (adapter only) Labelling CE

Know what's happening Reacheable via Wifi  Analysing power consumption and supply Measurement value logging with sensors Controlling and shifting Save elictricity   The ALLNET ALL3696 is the evolution result of the successful ALL369x powermeter series. This time for power meters with optical D0 interface. This helps to receive concrete and calibratted measurement values.    Measurement device for capturing and control of your power consumption with several measurement points Reachable everywhere via internet ( internet connection at the location of ALL3696 is needed)  Easy handling and installation via web interface and the optical reading head ALL3688, alternatively ALL3689  Integrated web server Alarm via E-mail if adjusted values are exceeded 4x D0 ports enables the connection with every D0 power meter with optical output (ALL3688/ALL3689)  Extensive consumption displaying with live diagram, chart function, table display Possibility to download the measurement values e.g. as a CSV data Interfaces: 1x network, 1x 300Mbit Wifi, 4x D0, 2x I2C sensor/ports, 2x external USB connections      Technische Daten: Element Spezifikation Interfaces:   2x magnetic connections for inductive transducers 1x50A (included), optional 50A / 200A und 800A available  1x D0 for power meters with optical output compatibility list 1x S0 contact with pulse counter 1x console port Internal data memory:  4GB USB flash memory stick Network connections: 1x RJ45 10/100Mbps 1x 2,4 GHz Wireless N, up to 150 Mbps Network protocols: HTTP/HTTPS, TCP/IP, SNTP, SMTP, SSH Operating systems: all network-compatible operation systems with browser Power supply: 100~240 VAC, 50/60 Hz, external 12V 1A power supply Power consumption: <3 watt maximum Housing: Aluminum housing, possibility of wall mounting Environment: Temperature range: 0 ~ 40 °C Humidity operation: 10% ~ 85% (not condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (not condensed) Labels: CE, RoHS Dimensions: 155 x 28 x 26 mm (lenghtx width x height)  Weight: 260 gramms (without accessories and package) Package content: 1x ALL3696 1x 50A inductive transducers SET "L1/L2/L3" 1x Wifi antenna 1x Ethernet cables 1x power supply 230VAC - 12V DC 1A 2x universal mounting brackets 1x quick install guide

Know what's going on! Find power guzzlers! Analyzing power consumption! Save electricity! Highlight: Meter to measure and control your current power consumption Direct connection of the current phases up to 32A per phase. Current measurement via integrated shunts Can be accessed anywhere via the Internet (Internet connection at the ALL3967 location is required) Simple operation and installation through web interface Integrated web server Alerting by email when a preset value is exceeded 1x I2C port for additional sensors/actuators of the ALLNET MSR measurement control rules series Comprehensive consumption display with live diagram, chart function, table display, etc. Possibility to download the measured values in database format, e. g. as CSV file Interfaces: 1x network, 1x USB, 1x I2C, Connection of the 3 phases L1/L2/L3/N  Features and WebGUI: The power meter offers you the possibility to graphically display your consumption. You can display a daily, weekly, monthly or annual graph and show or hide individual phases. The configuration page of the power meter allows you to set individual values within the device. Example: Labels and graph colours. If you want to continue using the determined values of the power meter or if you want to export them for archiving, you can easily download them as a CSV file via the web menu. Of course, there is also the chance to call up the values live via JSON. Technische Daten:   Interfaces: 1x Direct Phase Contacts (L1/L2/L3/N) max. 32A 1x I2C Port for additional sensors & actors of ALLNET Building Automation products http://www.allnet.de/en/allnet-brand/produkte/building-automation/automation-steuer-computer/building-automation-sensors/ 1x USB 2.0 4x TTL Outputs 4x Open Collector Output 1x Console RS232 1x OLED-Display 1x LAN 10/100Mbps 1x WIFI 1T1R 150Mpbs Network Connector: 1x RJ45 10/100Mbps Power supply: 100~240 VAC, 50/60 Hz, internes PSU Consumption: <5 Watt maximal Housing: DIN-Rail housing 12TE subunits Environment: Temperature operation: 0 ~ 40 °C Operating Humidity: 10% ~ 85% (non-condensing) Temperature Storage: -20 ~ 60 °C Humidity Storage: 5% ~ 90% (non-condensing) Dimensions: 160 x 91 x 63 mm (length x width x height) Weight: 370 grams (without packaging and accessories) Marks: CE, RoHS Package contents: 1 piece ALLNET ALL3697 QIG Manual 1 Patchcable 1m