ALLNET DIN-RAIL / Hutschienen PC LEC-6020A - Atom N2600

Universal power supply unit EDR-75-12 Input: 90*264VAC, 127~370VDC Output: 6.3A, 12V DC Operating temperature: -20°C to +60°C LxWxH: 32*125.2*102mm Connection via screw terminals The connection of electrical components and systems may only be carried out by only be carried out by qualified specialists!

Highlights: Super Voltage Booster -- 12V/24V/48VDC Power input Rugged Industrial 6 port Gigabit POE Injector 4x10/100/1000M TX PSE (802.3af/at POE+) 2x100/1000M SFP Slots for MiniGbic Modules Boost Voltage from 12/24/48VDC to 55VDC Voltage input range 12-56VDC, Operating temp: -40°C to +75°C Introduction This Super Voltage Booster --- The high power 6 port industrial POE+ Switch is equipped with our high efficiency ColdDesign technology which allows low input voltage, such as 12/24/48VDC be boost up to 55VDC to meet IEEE802.3at requirement. The ColdDesign technology will not only boost up Input Voltage, also reduce the excessive heat problem to a minimum. It accepts the input voltage as low as 12VDC, to be boost up to 55VDC. And it is also equipped with 2 port SFP ber that can be used as ber redundancy, cascaded to your other devices to expand your network application. It is being rigorously tested for your Security, Transportation and Telco application. Technical Details: IEEE Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3z 1000Base-X Gigabit Ethernet IEEE802.3x Flow Control and Back Pressure, IEEE802.3af for POE IEEE802.3at for POE+ Switch Architecture Back-plane (Switching Fabric): 12Gbps Data Processing Store and Forward Flow Control: IEEE 802.3x Flow Control and Back Pressure Jumbo Frame 9KB MAC address Table Size 1K Packet Buffer Size 1M Network Connector : 5xRJ-45 10/100/1000BaseT(X) auto negotiation, 4 Giga POE+ 802.3at/af 30W PSE per port Auto MDI/MDI-X function, Full/Half duplex                                             2 x SFP 100/1000M BaseX   Network Cable UTP/STP Cat.5e or above Cable EIA/TIA-568 10-ohm (100m) Fiber Cable (Multi-mode):50/125um,62.5/125um Fiber Cable (Single-mode): 9/125um Protocol CSMA/CD LED PW1(Power 1) Green, PW2(Power 2) Green, ERR (Fault) Amber, TX/RJ-45 port: LNK (Link/Active) Green, SPD(Speed) 10/100(OFF) ,1000 (Green) SFP Fiber Per port: Link (Green) Active Flash DIP Switch DIP 1:   OFF: Port 5 SFP ON (DEFAULT)               ON: Port 5 SFP OFF DIP 2:   OFF: SFP 1000M (DEFAULT)               ON: SFP 100M Reserve polarity protection Present Overload current protection Present Power Supply Redundant Dual DC 12V-56V Power Input Power Consumption 5.76W@12/24/48 VDC full load, Without POE Alarm Relay Contact Relay outputs with current carrying capacity of 1 A @24VDC,   Relay in short circuit mode when 2 powers are connected. in open circuit mode when only one power supply is connected POE power POE power per port 30watts. Maximum 36Watts per port at 12/24/48VDC input Maximum total power 126Watts at 24VDC and 48VDC power input. Maximum total power 65W at 12VDC power input Removable Terminal Block Provide 2 Redundant power, Alarm relay contact ,6 Pin Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire(AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm Operating Temperature -40° ~ 75° fully tested. Operating Humidity 5% to 95% (Non-condensing) Storage Temperature -40° ~ 85° C MTBF (mean time between failure) 510,304 hrs ( MIL-HDBK-217F) at 25°C Housing Rugged Metal, IP30 Protection Case Dimension (L x W x D) 142mmx43mmx105mm (LxWxD) Installation mounting DIN Rail mounting and Wall Mounting   Certifications: EN55022/24 ITE equipment EN50155 Railways Applications Electronic Equipment used on Rolling Stock EN55011 Industrial, Scientific and Medical (ISM) equipment EN50121-3-2 Railway Applications – Electromagnetic Compatibility – Part 3-2 Rolling Stock - Apparatus EN50121-4 Railway Applications – Electromagnetic Compatibility – Part4 Emissions and Immunity of the Signaling and Telecommunications Apparatus Safety IEC EN60950-1 EMC/EMS  CE, FCC, VCCI EMI FCC Part 15 Subpart B Class A, CE EN 55022 Class A EN 50155 / EN 60068-2-6 Vibration EN 50155 / EN 60068-2-27 Shock EN 50155 / EN 60068-2-32 Free Fall  

Highlights: Hardened 60W Gigabit POE converter designed with hardened Marvell IC 1x10/100/1000M 60W PSE (supports 802.3af/at) TX + 100/1000M SFP 48-56VDC Redundant Power-Input Operating temp: -40°C to +75°C   This Rugged 60 Watts Industrial POE converter is designed with hardened Marvell IC, it delivers 60Watts POE power to your PD. It also can tolerate extreme temperature in a harsh environment. Our ColdDesign technology will not only power up your PD device, also reduce the excessive heat problem to a minimum. It accepts the input voltage from 48VDC to 56VDC to meet IEEE802.3af/at required voltage. It is being rigorously tested for your Security, Transportation and Telco application.   Technical Detail: Element Specification Standards:   IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.3ab 1000BaseT IEEE 802.3z 1000BaseSX/LX IEEE 802.3x Flow Control Back Pressure IEEE802.af for PoE IEEE802.3at for PoE+ Network Connections: 1x 10/100/1000BaseT (RJ-45) 1x 1000BaseSX/LX SFP Module Slot Data Processing: Half/Full-Duplex on TP PoE: IEEE802.3at/af compatile Flow Control: IEEE802.3x Flow Control and Back Pressure Jumbo Frame 9KB Packet Buffer Size 1M MAC adress Table Size 2K Network Cable: TP:10/100/1000BaseT Cat. 5, 5E, 6 UTP/STP, till 100 m 1000BaseSX: 62.5/125μm Multi Mode LWL, till 220 m 50/125μm Multi Mode LWL, till 550 m 1000BaseLX: 9/125μm Single Mode LWL POE Pin Assignment: 60 watts 4 pairs V+, V+, V-, V- for pin 1, 2, 3, 6 V+, V+, V-, V- for pin 4, 5, 7, 8 DIP Switch: To select SFP speed 100M or 1000M. Reverse polarity protection: Present Overload current protection: Present LED: PW1(power 1) Green: ON- power good, OFF-power failed UTP LEDS: Amber ON- PD detected,  Green ON – Link/active SFP LED: Green ON – SFP detected Power Supply: 4pin Terminal Block 48V-56V VDC Power Input SW (Relay): Relay switch for alarm Power Consumption: 2W@48VDC without PoE PoE Power: Maximum PoE Power 72W at 56VDC Input Alarm Relay Contact: Relay outputs with current carrying capacity of 1 A @24VDC, Relay in short circuit mode when power fails. in open circuit mode when power supply is connected Removable Terminal Block: Provide 4 pin terminal block Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire(AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm Case Dimension (L X W X D)mm 103.5mmx32mmx81.5mm (LxWxD) Installation mounting: DIN Rail mounting and Wall Mounting Housing: Rugged Metal, IP30 Protection MTBF ( mean time between failure) 510,304 hrs ( MIL-HDBK-217F) at 25°C Environment: Operating Temperature: -40° ~ +75° °C Operating Humidity:  5% ~ 95% (non condensing) Storage Temperature: -40 ~ 85 °C Storage Humidity: 5% ~ 95% (non condensing) Marks: CE, FCC, VCCI EN55022 Class A EN55022/24  ITE Equipment EN55011       Industrial, Scientific and Medical (ISM) equipment IEC EN60950-1 Sicherheit Shock: EN50155 / EN 60068-2-27 Free Fall: EN5055 / EN 60068-2-32 Vibration: EN 50155 / IEC 60068-2-6 EMI: FCC Part 15 Supbart B Class A CE EN 55022 Class A

LC-connection 1.125G 850 nm multimode, SFP, 550m range, industrial -40 -+85degrees, for Allnet/D-link/Netgear/Allied/Lancom/Zyxel/Entersys/ZTE/Planet/Avago/ Microtics/Ubiquiti/Avaya

LC-connection 1.125G 1310nm singlemode, SFP, 10km range, Industrial -40 -+85degrees, for Allnet/D-link/Netgear/Allied/Lancom/Zyxel/Entersys/ZTE/Planet/Avago/ Microtics/Ubiquiti/Avaya

LC connector, MultiMode 850nm, Industrial -40 -+85deg, Max. Cable lengths with 50/125µm MultiMode cable. OM2 80m, OM3 300m, OM4 500m for Allnet/AlliedTelesyn/Avago/Avaya/Cambium/D-link/Entersys/Mikrotik/Netgear/Lancom/QNAP/Planet/Ubiquiti/Zyxel/ZTE

LC connector, 1310nm SingleMode, Industrial -40 -+85deg, Max. Range 10km with 9µm SingleMode cable. DDM support - SFF8472 monitoring level measurement for Allnet/AlliedTelesyn/Avago/Avaya/Cambium/D-link/Entersys/Mikrotik/Netgear/Lancom/QNAP/Planet/Ubiquiti/Zyxel/ZTE

Highlights: 60 Watts, selectable Mode A and Mode B Industrial Gigabit POE Injector with voltage booster accept 24 VDC to boost up voltage to 55V for 60Watts application 1x10/100/1000M TX PSE (802.3af/at POE+) TX 1x10/100/1000M TX Operating temp: -40°C to +75°C Introduction This Super Voltage Booster --- 60 Watts, high power Single port industrial POE Injector is equipped with our high efficiency ColdDesign technology which allows low input voltage, such as 24/48/56 VDC be boost up to 55VDC to provide 60Watts to 72 Watts power to your security equipment by a 4-pin selectable dip switch. The ColdDesign technology will not only boost up Input Voltage, also reduce the excessive heat problem to a minimum. It accepts the input voltage as low as 24/48 VDC to boost up to 55V to meet IEEE802.3af/at required voltage. This built-in 4 pin dip switches are able to select POE for Mode B or Mode A, to select standard IEEE802.3at 30Watts or high power 36Watts, and to select 2 pair or 4 pair for 30/36Watts or 60/72Watts power output. It is being rigorously tested for your Security, Transportation and Telco application. Technical Details: IEEE Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE802.3af for POE IEEE802.3at for POE+ Network Connector : 1xRJ-45 10/100/1000BaseT(X) Data 1xRJ-45 10/100/1000BaseT(X) PSE with POE Output power Network Cable UTP/STP Cat.5e or above Cable EIA/TIA-568 10-ohm (100m) Protocol CSMA/CD LED PW1(power 1) Green: ON- power good, OFF-power failed PW2(power 2) Green: ON- power good, OFF-power failed Mode A : ON-  End Span PD detected Mode B: ON – Mid Span PD detected 4 Pair: ON – 60W PSE in active mode.             OFF – 30W PSE in active mode. POE Pin Assignment Default: Mode A (End Span) V+, V+, V-, V- for pin 1, 2, 3, 6 DIP switch setting can be changed to Mode B, V+, V+, V-, V- for pin 4, 5, 7, 8 DIP Switch To select 2 pair (30/36Watts) or 4 pair (60/72Watts) To select Mode A, or Mode B To select standard IEEE802.3at 30watts or high power POE 36Watts Reverse polarity protection Present Overload current protection Present Power Supply 2 Redundant power source 24V-56V VDC Power Input, Power Consumption 1 W@24/48 VDC full load, Without POE POE power Maximum POE power 72watts at 24/48VDC input Removable Terminal Block Provide 4 pin terminal block Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire(AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm Operating Temperature -40° ~ 75° fully tested. Operating Humidity 5% to 95% (Non-condensing) Storage Temperature -40°~85° MTBF (mean time between failure) 510,304 hrs ( MIL-HDBK-217F) at 25°C Housing Rugged Metal, IP30 Protection Case Dimension (L X W X D)mm 103.5mmx32mmx81.5mm (LxWxD) Installation mounting DIN Rail mounting and Wall Mounting   Certifications: EN55022/24 ITE equipment EN55011 Industrial, Scientific and Medical (ISM) equipment Safety IEC EN60950-1 EMC/EMS  CE, FCC, VCCI EMI FCC Part 15 Subpart B Class A, CE EN 55022 Class A EN 50155 / EN 60068-2-6 Vibration EN 50155 / EN 60068-2-27 Shock EN 50155 / EN 60068-2-32 Free Fall

Lichtgrau ähnlich RAL7035, T150/B483/H133mm, wird an der 19" Ebenen befestigt B465mm Befestigungslochabstand, Nutztiefe 140mm, Din-Railschiene T6mm zur aufnahme von Industrieswitchen und anderen Dinrail Geräten,