FriendlyELEC

Product Description: 1.Frequency Range: 690-960/ 1710-2620MHz. 2.Bandwidth: 70/910MHz 3.Gain: 5dBi 4.VSWR: =1.5 5.Polarization Linear: Vertical 6.Omnidirectional Antenna 7.Input Impedance(ohm): 50 8.Rated power(W): 50 9.Connector: SMA straight connector with male pin) 10.Weight: 41g

Universal power supply 5V3A fixed cable to USB-C Daten: Input : 100V - 240V ~50-60Hz 0,5A Output: 5V ---3000mA Energy Efficiency Class: VI Kabel 2m AWG20 USB-C

Universalnetzteil 5V3A mit Micro USB Daten: Input : 100V - 240V ~50-60Hz 0,5A Output: 5V ---3000mA Kabel 2m Micro USB

X710 Display   Informationen: https://wiki.friendlyarm.com/wiki/index.php/LCD-X710   Passend für :  Applicable Platforms Debian Android Linux+Qt NanoPi 2 NanoPi 2   NanoPi M2 NanoPi M2   NanoPi 2 Fire NanoPi 2 Fire   NanoPi M3 NanoPi M3   NanoPC T2 NanoPC T2   NanoPC T3 NanoPC T3   Smart4418 Smart4418     Tiny4412 Tiny4412 One-Wire-Technologie Wie bei den meisten ARM-Boards haben wir festgestellt, dass die Verwendung der ADC-Wandlung der CPU bei großen LCDs (7" und größer) mit Vier-Draht-Resistiv-Touch nicht sehr gut funktioniert. Einige Hersteller verwenden ein externes USB- oder UART-Modul, um diese LCDs anzuschließen. Um die Hardware-Ressourcen der CPU zu schonen und die Verwendung externer Module zu minimieren, haben wir die Ein-Draht-Technologie entwickelt, die nur einen einzigen GPIO-Pin verwendet, und wir haben diese Technologie in alle unsere LCD-Controller-Boards integriert. Bei dieser Technologie kommuniziert eine MCU mit dem Chip des Touchpanels (wir verwenden den ADS7843-Chip oder andere Chips, die mit dem ADS7843 kompatibel sind) und verarbeitet die analogen Signale des Vierdraht-Widerstands und gibt die gefilterten stabilen Signale über GPIO an das ARM-Board aus. Wir haben diese Technologie in verschiedenen LCDs getestet, und sie funktionierte selbst bei einem großen LCD von 19" sehr gut, und einige häufig beobachtete Probleme wie Screen Flipping und Jittering traten nicht auf. Heute haben die meisten LCDs, die kleiner als 12" sind, eine LED-Hintergrundbeleuchtung. Wir verwenden die MCU des One-Wire, um auch die Hintergrundbeleuchtung zu verarbeiten. Die Hintergrundbeleuchtung wird mit einer Reihe von Werten eingestellt. Der Benutzer kann einen Wert für die Hintergrundbeleuchtung einstellen und dieser Wert wird über den GPIO-Pin des One-Wire an die MCU zur Verarbeitung weitergeleitet. Jedes FriendlyARM-LCD-Modul hat eine eindeutige ID, die in der MCU des one-wire gespeichert ist. Wenn die MCU die ID-Informationen aus den GPIO-Signalen ausliest, erkennt sie das LCD-Modell und weist den Bootloader an, den entsprechenden LCD-Treiber zu laden, wodurch ein FriendlyARM-LCD plug and play wird. Bei der Ein-Draht-Technologie für unsere LCDs mit kapazitivem Touch haben wir den Chip des resistiven Touch-Panels entfernt, aber die Funktion zur Einstellung der Hintergrundbeleuchtung und die ID-Informationen des LCDs beibehalten. Daher ist die Kommunikation zwischen dem kapazitiven Touch und dem ARM-Board immer noch Standard IIC. Achtung: Die Ein-Draht-Technologie unterscheidet sich von der allgemein bekannten Single-Bus-Kommunikation. Auf dem ARM-Board verwenden wir einen PWM-Timer (nicht PWM-Pins), um die Kommunikationsfrequenz (9600Hz) zu erzeugen. Weitere Details entnehmen Sie bitte dem Quellcode des Treibers.      

Rock Pi adapter SD card - MicroSD extension cable This extension cable can be used to extend a micro SD slot. Thanks to the flexibility of the cable it is possible to route the slot into a housing, for example. The cables are particularly suitable for Raspberry Pi, Rock Pi etc. Connection: micro SD plug -> micro SD socket / slot (with push/eject function) For micro SD/SDHC cards Colour: white; Cable length: approx. 15cm  

Rock Pi adapter SD card - MicroSD extension cable This extension cable can be used to extend a micro SD slot. Thanks to the flexibility of the cable, it is possible to move the slot into a housing, for example. The cables are particularly suitable for Raspberry Pi, Rock Pi etc. Connection: micro SD plug -> SD socket / slot (with push/eject function) Für SD/SDHC cards Colour: white Cable length: approx. 15cm Same article as 162898

ALLNET GSM antenna 2dbi zbh. 4G/LTE stub antenna

NanoPC-T6 LTS (as "T6") is a one-for-all high performance open source platform for edge computing, designed and developed by the FriendlyElec team.  It has two 2.5G Ethernet ports. It is based on Rockchip's RK3588, and has 4GB/8GB/16G LPDDR4x RAM and an optional 32GB/64GB/256/0GB eMMC flash. It works with systems including OpenMediaVault, FriendlyWrt, Android, Android TV, Debian, Ubuntu etc. It supports GPU and VPU acceleration. T6 is a compact board of 110 x 80 mm with rich hardware resources and an optional CNC metal case. It has 2 HDMI output ports and 1 HDMI IN port. T6 can play video streams including 8K60p H.265/VP9 , 8K30p H264 etc and record video streams including 4K60p H.265. T6 has one M.2 B-Key slot that supports an M.2 NVME SSD disc, one M.2 E-Key that supports an M.2 2230 WiFi module. In addition, T6 has one USB 3.0 and two USB 2.0 ports, and one full-featured USB-C port that is powered by DC-12V. In summary, T6 is well suited for enterprise customers to develop mini machine vision systems with multiple Ethernet ports and for embedded system hobbyists to explore and implement prototype designs. 2 Hardware Spec SoC: Rockchip RK3588 CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz) GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2 VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder NPU: 6TOPs, supports INT4/INT8/INT16/FP16 RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz eMMC Flash: 32GB/64GB/256GB eMMC, at HS400 mode Nor Flash: 32MB SPI Nor Flash microSD: support up to SDR104 mode Ethernet: 2 x PCIe 2.5G Ethernet 1 x USB 3.0 Type-A, 1 x Full function USB Type-C™ port, support DP display up to 4Kp60, USB 3.0 2 x USB 2.0 Type-A Video input: 1 x standard HDMI input port, up to 4Kp60 2 x 4-lane MIPI-CSI, compatible with MIPI V1.2 Video output: 2 x standard HDMI output ports compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation one support displays up to 7680x4320@60Hz, another one support up to 4Kp60 Support RGB/YUV(up to 10bit) format 2 x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1 Audio: 1 x 3.5mm jack for stereo headphone output 1 x 2.0mm PH-2A connector for analogue microphone input GPIO: 40-pin 2.54mm header connector up to 2 x SPIs, 6 x UARTs, 1 x I2Cs, 8 x PWMs, 2 x I2Ss, 28 x GPIOs M.2 connectors one M.2 M-Key connector with PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s one M.2 E-key connector with PCIe 2.1 x1 and USB2.0 Host others: 10 Pin 2.54mm header connector including Debug UART(3.3V TTL) and 2 x USB 2.0 Host 2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS one 38Khz IR receiver MASK button for eMMC update, reset button, and Power button one 5V fan connector USB-C to Debug UART 2 x GPIO Controlled LED (SYS, LED1) Power supply: 5.5*2.1mm DC Jack & 2-pin 3.5mm pitch connector, 12VDC input. PCB: 8 layers, 110x80x1.6mm Ambient Operating Temperature: 0? to 70? Further information can be found here: LINK ext. website

Heatsink especially for FriendlyELEC NanoPi NEO to screw on the bottom side of the board. 12,5x12,5x1,5mm cooling pad Bulk of 50 (Thickness of cooling pads may vary, for industrial production please check, we do not assume liability).    

The S70D LCD is a FriendlyARM developed LCD with resistive touch panel. Its resolution is 800 x 480. Its backlight is adjustable via FriendlyARM’s one-wire technology. It works with FriendlyARM’s Mini2440, Mini6410, Mini210S, Tiny4412 and NanoPi 2 under Linux, WinCE and Android. Its driver is open source.

FriendlyELEC 7" inch capacitive touch LCD(S702)

Classification: UHS-I, Class 10 - read: 85mb/s - write: 21MB/s - Features: incl. SD adapter. The super-fast and reliable EMTEC MicroSDHC memory cards are especially designed for tablets and current smartphones: - Increase storage capacity and enjoy more applications and content (videos, photos, etc.). - Take advantage of all the benefits and possibilities of the latest generation devices (such as Full HD recording) thanks to the higher transfer rates. Usable in all devices that support MicroSDHC and / or Micro SDXC standards.

Heatsink especially for FriendlyELEC NanoPi NEO to screw on the bottom side of the board. 12.5x12.5x1.5mm cooling pad (thickness of cooling pads may vary, for industrial production please check, we assume no liability).  

  CPU Model: Rockchip RK3568B2Number of Cores: Quad-core ARM Cortex-A55Frequency: 4 x Cortex-A55 up to 2.0GHz GPU Mali-G52 1-Core-2EE, supports OpenGL ES 1.1/2.0/3.2, Vulkan 1.0/1.1, OpenCL 2.0 Full Profile VPU 4KP60 H.265/H.264/VP9 video decoder, 1080P60 H.264/H.265 video encoder NPU Support 0.8T Memory RAM: 1GB/2GB/4GB LPDDR4X Storage MicroSD Slot x1: support UHS-I Flash:0GB/8GB/32GB eMMC Connectivity Ethernet: PCIe 2.5G Ethernet Ethernet x2, RTL8125BG chipM.2 E-Key x1: PCIe2.1 x1, USB 2.0 x1, supports M.2 WiFi and Bluetooth Module Video Output HDMI: support HDMI1.4 and HDMI2.0 operationsupport up to 10 bits Deep Color modessupport up to 1080p@120Hz and 4096x2304@60Hzsupport 3-D video formats USB USB 3.0 Host x2: USB 3.2 Gen 1 Type-AUSB-C x1: Power Only(5V) Pin-header Debug: Debug UART x1, 3 Pin 2.54mm header, 3.3V level, 1500000bps LED SYS LED(Red) x1WAN LED(Green) x1LAN1 LED(Green) x1LAN2 LED(Green) x1 Button MASK Button x1 for eMMC updateUser Button x1 Others RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TSWorking Temperature: 0? to 70? Power USB-C, 5V input OS Support FriendlyWrt 21.02FriendlyWrt 22.03Android 12 TabletAndroid 12 TVFriendlyCore Lite 20.04Debian 10 DesktopDebian 11 DesktopBuildroot Kernel version Linux-5.10-LTSU-boot-2017.09 PCB 8 Layer Weight 38g(without Case) / 149g(with Case) Dimension 58x58x1.6mm (without Case) / 62.5x62.5x29mm (with Case)

FriendlyELEC - 64GB eMMC Module for Booting OS ohne SD-Adapter                                                                                                        

FriendlyELEC Zero2 Combo with Case 1GB SoC: Rockchip RK3528A CPU: Quad-core ARM Cortex-A53 GPU: ARM Mali-450 GPU VPU: 4K H265/H264 60fps decoding RAM: 1GB/2GB LPDDR4/LPDDR4X Flash: Supports eMMC Module Ethernet: one Native Gigabit Ethernet M.2 Key-E 2230 connector with PCIe 2.1 USB Ports: One USB 2.0 Host Type-A port One USB 2.0 Device Type-C port for eMMC upgrade One microSD Slot One 30-pin FPC GPIO connector Debug: Debug UART, 3.3V level, 1500000bps LEDs: 2 x GPIO Controlled LEDs (SYS & LED1) others: 2 Pin 1.27/1.25mm battery connector for Low-power RTC RESET Button, RECOVERY Button, and MASK Button for eMMC upgrade Power supply: DC 5V/2A, via USB-C connector or 2.54mm Header PCB Size: 45*45*1.2mm Temperature measuring range: 0? to 80? https://wiki.friendlyelec.com/wiki/index.php/NanoPi_Zero2

FriendlyELEC NanoPi Neo with 512MB Please order a suitable heat sink for the processor (Art. 134871) separately. - SoC: Allwinner H3 Quad Core Cortex A7 1,2Ghz - DDR3 RAM: options: 512M RAM - MicroSD Slot x1 - Connectivity: lO/lOOM Ethernet port - USB Host: 1x 2.0 Host Typ A - Micro USB: 1 x Micro USB,OTG, for data transmission and power input - Debug Serial Port: 4Pin 2.54mm pitch pin header - GPIO: 2.54mm pitch 40pin, compatible with Raspberry Pi's GPIO. It includes UART,   SPI, |2C, PWM, IO etc - User Key: 1 x Power, 1 x Reset - LED: 1 x Power LED, 1 x System LED - Power: DC 5V/2A - PCB Dimension(mm): 40x40mm - OS/Software: u-boot, Ubuntu-Core   Wiki: http://wiki.FriendlyELEC.com/wiki/index.php/NanoPi_NEO  

FriendlyELEC - 32GB eMMC Module for Booting OS ohne SD-Adapter