RUCKUS Zubehör Power over Ethernet (PoE) Adapter R550/R650/R750/R850/R720/T710/T610/T750 60 Watt - PoE module (10/100/1000Mbps) • Input: 100-240VAC ~ 50/60Hz 1.0A • Output: 48VDC 1250mA (60W) • Data port: RJ-45 jack • PoE/data port: RJ-45 jack • Dimensions 123 x 61 x 40 mm

Power-over-Ethernet (PoE) adapter for products with (1.0/2.5/5.0/10.0 Gbps) PoE inputs. Indoor-rated. Supports power up to 60W. T710, T710s, T750, R550, R560, R650, R720, R730, R750, R760, R850

ICX 7150 Compact Switch, 2x 100/1000/2.5/5/10G PoH ports, 2x 100/1000/2.5G PoH ports, 6x 100/1000/2.5G PoE+ ports, 2x 10G SFP+ uplink-ports, 240W PoE budget, L3 features (OSPF, VRRP, PIM, PBR)

Highlights: support IEEE802.3, IEEE802.3u, IEEE802.ab,IEEE802.3af, IEEE802.3at and LT PoE 90W 1 Port 10/100/1000 Base-T (Data) for connection to a switch, and 1 Port 10/100/1000 Base-T (Power/Data) for connection to a PoE Device (PD) Automatic detection of whether the connected device is PoE capable   With the ALLNET ALL048900V2 High Power PoE Injector you install your PoE-enabled IP devices such as wireless access points, VoIP phones and much more totally independent of existing electrical outlets.   So you can choose the best locations for example WLAN access points installations in a building regarding the wireless technology, without having to worry about power cabling.   Non-PoE switches can be efficiently „upgraded“ with Power over Ethernet, especially when you only need a few ports with PoE power supply. Here the ALL048900V2 saves the expensive purchase of a PoE switch.   The ALLNET ALL048900V2 supports the IEEE802.3af standard with a power of 15,4 Watt, the IEEE802.3at high power standard with 30 Watt and the LT PoE with 90 Watt power.   The ALL048900V2 must not be configured. It has an RJ45 jack and an RJ-45 output connector, which are connected to this switch and the end device to the PoE injector. The cable length can here, as usual in Ethernet, up to 100 meters between the switch and terminal in total.   The compact design and the metal case of the ALLNET ALL048900V2 can be very inconspicuous installed and is extremely robust.    Technical Details:   Element Spezification Standards: IEEE802.3af Power over Ethernet IEEE802.3at Power over Ethernet enhancements LT PoE 90W IEEE802.3 10BaseT IEEE802.3u 100BaseTX IEEE802.ab 1000BaseT Ethernet ports: 1x RJ45 10/100/1000Mbps for connection to passive switch or hub 1x RJ45 10/100/1000Mbps for connection to PoE device LED indikators: Power / PoE Act / Status Power input: 44~57V Power consumption:   System: 5W (Max.) LT PoE++: up to 90W   Attached power adapter: Input: 100~240VAC Output: 56VDC/2A, 112W (Max.) Case: Metal case, wall-mountable Dimension: Length/Width/Height: 102 x 75 x 23 mm Weight: 280g (o. Netzteil und Verpackung) Environment: Temperature operating: 0 ~ 40 °C Humidity operating: 10% ~ 90% (non-condensing) Temperature storage: -25 ~ 90 °C  Marks: FCC Class A, CE

ALLNET 10G fibre media converter Highlights: Media converter from 10GBase-T to 10G Base-SFP+ fibre port Dependently compatible with 2.5G-Base-T / 5G-Base-T Cooper and 2.5G-Base-X / 5G-Base-R fibre optic Working mode: 1000Base-T to 1000Base-X / 2.5GBase-T to 2500Base-X / 5Gbase-T to 5GBase-R / 10Gbase-T to 10GBase-R 1x 10G Cooper port & 1x SFP+ slot optional SFP+ modules required The 10G Base-T to 10G Base-R Media Converter supports two types of media for network connections such as 10GBase-T and 10GBase-FX. The Bridge Media Converter is equipped with a 10Gbase Ethernet PHY chip that smoothly connects two types of segments together. IMPORTANT: The following MODI are possible:1000Base-T  <-> 1000Base-X Fibre and vice versa 2.5GBase-T  <-> 2500Base-X Fibre and vice versa 5Gbase-T  <->  5GBase-R Fibre and vice versa 10Gbase-T  <-> 10GBase-R Fibre and vice versa Technical details: Standards 1000Base-T 2.5GBase-T 5Gbase-T 10Gbase-T 1000Base-X 2500Base-X 5GBase-R 10GBase-R Media Supported 1000Base-T: Cat5 UTP/STP. MAX 100m; 2.5GBase-T: Cat5e UTP/STP. MAX 50m; 5GBase-T: Cat5e UTP/STP. MAX 50m; 10G Base-T: Cat6a UTP/STP. MAX 50m; Port Type RJ45, SFP Slot Work mode 1000Base-T to 1000Base-X 2.5GBase-T to 2500Base-X 5Gbase-T to 5GBase-R 10Gbase-T to 10GBase-R Power Supply 12V DC Power consumption: MAX 5W Operation Tempera tore 0°C to 55°C Relative Humidity 5% to 80% (non-condensation)

ALLNET PoE Injector Gigabit PoE & PoE+ (15,4W/30W) / plastic housing / "ALL0488v6   Highlights: PoE injector according to IEEE802.3af/at with max. power of 30W 2x RJ45 Gigabit Ports PoE Output 55VDC@30W Midspan PoE PIN's 4/5 (+) and 7/8(-) internal power supply unit compact design incl. 1.5m power cable with IEC-C5 to IEC-CEE7 protective contact cable NEW: Wall mounting capable Intelligent power supply via network without switch With the ALLNET ALL0488V6 Power over Ethernet Injector you can install your PoE-enabled IP devices such as WLAN access points, VoIP phones and much more absolutely independent of existing power sockets. For example, WLAN access points can be installed in the most ideal locations in a building without having to worry about power cabling. Switches that are not PoE-capable can be "retrofitted" with Power over Ethernet at a reasonable price, especially if only a few ports with PoE supply are required. Here, the ALL0488V6 saves the purchase of a PoE switch. The ALLNET ALL0488V6 supports the IEEE802.3af & IEEE802.3at standard with a maximum power of 30W Watt. The ALL0488V6 does not need to be configured. It has an RJ45 input socket and an RJ-45 output socket, which is used to connect the switch and terminal device to the PoE injector. The cable length here can be up to 100 meters between switch and terminal device in total, as is usual in Ethernet. Due to its compact design, the ALLNET ALL0488V6 can be installed very easy. It has an internal power supply and supplies the PoE voltage on pins 4/5 (+) and 7/8 (-). Technical Details: Element Specifikation Standards: IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-Tx Fast Ethernet IEEE802.3ab 1000Base-T Gigabit Ethernet Support terminal equipment with IEEE802.3af/at, PoE++ RoHS Compliance WEEE Compliance Ethernet Ports: 1x RJ45 10/100/1000 Mbps for connection to switch or hub 1x RJ45 10/100/1000 for connection to PoE end device PoE Output: PoE IEEE802.11af/at, Power pins: 4/5(+) 7/8(-) Power supply: 100 - 240VAC, internal power supply / Output: 55V/550mA incl. connection cable earth contact on IEC320-C5 "Kleeblat/Micky-Mouse" approx. 80cm length Power consumption: 30 Watt maximum with connected PoE end device AC Surge Protection: 1.0KV (5P/5N) L-N 1.2/50 (8/20) Tr/Th us 2.0KV (5P/5N) L-PE 1.2/50 (8/20) Tr/Th us N -PE Housing: Plastic housing Mounting: Wall-mounted Dimensions: length/width/height: 140 x 63 x 33 mm Environment: Operating Temperature: 0 ~ 40 °C Operating Humidity 10% ~ 90% (non-condensing) Storage Temperature: -20 ~ 90 °C Storage Humidity: 10% ~ 90% (non-condensing) EMI: FCC CFR47 Part 15 EN55024 EN55032 EMS: IEC61000-4-2(ESD) ± 6kV(contact), ±8kV(air) IEC61000-4-3(RS) 10V/m(80MHz~2GHz) IEC61000-4-4(EFT) Power Port: ±2kV; Data Port:±1kV IEC61000-4-5(Surge) Power Port:±1kV/DM, ±2kV/CM IEC61000-4-6(CS) 10V(150kHz~80MHz) Immunity: IEC60068-2-6(Vibration) IEC60068-2-27(Impact) IEC60068-2-32(Free Fall) Marks: CE; FCC

The ALL0489v4 2.5GBASE-T PoE+ Injector provides up to 30 watts of power and a 2.5 Gigabit data connection anywhere in the network infrastructure. This device feeds DC power over a CAT5e UTP cable, increasing flexibility in positioning a PoE-enabled device when a nearby power source is lacking. It supports PoE+ standard (802.3af 15.4W & 802.3 at 30W) and up to 30W power for connected PD devices. It can easily connect to powerful devices such as VoIP phones, APs and IP cameras. The device is plug-and-play without software configuration. It supports 0?~45? Operating temperature and metal housing design, which is more suitable for various environmental applications. Provides a PoE LED status signal, which gives an easily detectable PoE connection status. Over-current and short-circuit protection are also supported to ensure safety. KEY FEATURES 10/100/1000/2500 Base-T (Data) for connection to Ethernet switch 10/100/1000/2500 Base-T PoE (Power/Data) for connection to the PoE device (PD) Auto-Negotiation Automatically detects if the connected device is PoE capable to avoid sending power to a non-PoE device. Complies with IEEE802.3, 802.3u, 802.3ab, 802.3bz, 802.3af, 802.3at standards. 802.3af (15.4W) and 802.3at (30W) PoE power output. one PoE Link LED one GND screw full range (100~240VAC) internal power supply No fan, passive cooling, small size, silent design MTBF: over 50,000 hours@45? ESD IEC61000-4-2 contact +/-4KV, air +/-8KV EFT IEC61000-4-4 power 2KV, LAN 1KV Overload protection IEC61000 4-5 cable to cable & cable to GND Level3 2KV PRODUCT SPECIFICATIONS Standard IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3bz, IEEE802.3af, IEEE802.3at Standards Interface: 1 * PoE+ 10/100/1000/2500Mbps RJ-45 port, 1 * 10/100/1000/2500Mbps RJ-45 port LED indicators: power supply (green), PoE link (green) Emission: FCC, CE, VCCI Class B Safety: CE LVD Operating temperature & humidity: 00- 450C; 10%~90% RH. Storage temperature & humidity: 20°- 70°C; 5%~90% RH. Dimension: 130 x 62 x 36 mm Switching power supply: +54V/40W, 100~240VAC input, 47~63Hz. Overload protection  

Highlights:   Plug and Play installation Reliable surge protection for all devices with a network connection: • Switche, Router, Firewall, xDSL Modem, ISDN, NoteBook, PC / Server • Television • Multimedia Devices Protect your network equipment from power surges by lightning The ALLNET ALL95100 provides a cost-effective and reliable protection against damage to sensitive equipment. Housed in a compact body the ALLNET surge protection is simply inserted between the network cable or xDSL / ISDN connection and the equipment to be protected.   Without con guration the device is immediately protected from power surges. Along with a regular surge protector and bonding can be for example the infrastructure in safety-relevant areas permanently protected. Not only indoors, but also particularly like the outside, the ALL95100 is used effectively in conjunction with PoE enabled IP Cam‘s and wireless access points. Technical Details: Element Spezifikation Network Interface: 2x RJ45 10/100/1000Mbps PoE-Capability: IEEE802.3af, at, LTPoE++ bis 90W Arrest capacity: 10kA (8/20µs), 100A (10/1000µs) Ignition voltage: 90VDC ±20% (Pair to Earth) <450V (bei 100V/µs) <600V (bei 1kV/µs) Diff. Clamping: <15V, <5ns, 30Apk (Pair wire to wire) Diff. Capacity: <4.0pF Lines protected: (Pins)1 - 8 (at 8 pin modular plug) Test mark: IEEE 802.3, CAT 5, 6 ESD Protection: IEC 61000-4-2 class 4 (10kV CD) Housing: metal case Enviroment: Temperature operating: -15 ~ 40 °C Humidity operating: 10% ~ 95% (non condensed) Marks: CE, RoHS Maße: 82 x 25 x 25 mm (Length x Width x Height) weight: 200 Gramm Package content: -ALLNET ALL95100 -QIG

ALLNET Switch full managed 24 Port Gigabit 390W / 24x PoE+ / 4x SFP / FANLES / 19" / "ALL-SG8626PM" Cost-effective 24 Port Smart Managed Gigabit Layer-2 Switch + 4x SFP MiniGbic Slots without Fan for Desktop and 19" Rack Installation Highlights: 24 Port Gigabit Layer2+ Switch Architecture Port 23/24 combo ports for TP or SFP + Port 25/26 SFP slots Supports various PoE management functions, including PoE shedule, PoE PD alive, etc. Supports SFP DDM & cable diagnostics Supports G.8032 ERPS, self-detection time < 20 ms Supports port aggregation 4KV surge protection, 6KV contact/8KV air ESD protection Totally fanless, no more annoying noise....  max. 390W budget 19 "inch angle or wall/table mounting possible ALL-SG8626PM is a layer 2+ full managed switch PoE, which supplies 24**10/100/1000M RJ45 ports and 4*1G uplink  SFP slot ports ( 2 shared combo), with 24 port PoE with IEEE802.3 af/at standards, single port POE power output up to 30W. Rich PoE Management Function Being the managed PoE switches for CCTV surveillance, wireless and VoIP networks, ALL-SG8626PM features the following special PoE management functions: PoE PD-alive check Scheduled power rebooting PoE schedule PoE usage monitoring Soft-reboot PoE Non-stop PoE port power feeding priority Smart PoE PD-Alive Check ALL-SG8626PM managed PoE switch can be configured to monitor connected PD status in real time. Once the PD stops working and responding, ALL-SG8626PM will resume the PoE port power and bring the PD back to work. They will greatly enhance the network reliability through the PoE port resetting the PD’s power source and reducing administrator management burden. PoE Schedule Function for Energy Saving For environmental protection purpose, the ALL-SG8626PM switch Ethernet PoE can effectively control the power supply besides its capability of giving high watts power. The PoE schedule function helps to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or enterprises save power and money. Scheduled PD Re-starting The ALL-SG8626PM smart switch PoE allows each of the connected PoE IP cameras or PoE wireless access points to reboot at a specific time each week. Therefore, it will reduce the chance of IP camera or AP crash resulting from buffer overflow. Fast Recovery Redundant Ring for Critical Network Applications The ALL-SG8626PM supports redundant ring technology and features strong, rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. In a certain simple Ring network, the recovery time of data link can be as fast as 20ms. Strong Layer 2 Features The ALL-SG8626PM layer 2 Ethernet switch can be programmed for advanced Layer 2 switch management functions such as dynamic port link aggregation, 802.1Q tagged VLAN, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), QoS, bandwidth control, IGMP snooping and MLD snooping. Via the aggregation of supporting ports, the ALL-SG8626PM allows the operation of a high-speed trunk group that comes with multiple ports and supports fail-over as well. Efficient and Various Management Methods For efficient management, the ALL-SG8626PM is equipped with console, Web and SNMP management interfaces. With the built-in Web-based management interface, it offers an easy-to-use, platform-independent management and configuration facility. For text-based management, it can be accessed via Telnet and the console port. For standard-based monitor and management software, it offers SNMPv3 connection which encrypts the packet content at each session for secure remote management. Intelligent PoE Switch SFP DDM Function The ALL-SG8626PM supports SFP-DDM (digital diagnostic monitor) function that greatly helps network administrator to easily monitor real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. Technische Daten: Model ALL-SG8626PM Copper Ports 22-10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports Combo Interfaces 2x 100/1000BASE-X SFP interface shared with port-23 and port-24; Supports 100/1000Mbps dual mode and DDM Fiber Ports 2-100/1000BASE-X SFP interfaces, supports 100/1000Mbps dual mode PoE Ports 1~24-802.3af/802.3at PoE Injector Ports Console Ports 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1) Switch Architecture Store-and-Forward Switch Fabric 52 Gbps/non-blocking Throughput 38.69Mpps @64 bytes Address Table 8K entries Share Data Buffer 4 Mb Jumbo Frame 9600 Bytes SDRAM 1Gb Flash Memory 128Mb Flow Control IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex Reset Button >2 sec.: Factory default and reset Power Supply 100~240V AC, 50/60Hz, 4A (max.) Power Consumption Max. 400 watts/1122 BTU PoE Standards IEEE 802.3af Power over Ethernet/PSE IEEE 802.3at Power over Ethernet Plus/PSE PoE Power Supply Type Per Port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af) Per Port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at) LED Indicators Power: Green Solid on- power work normal, off- power disconnected System: Green Blink -work normally, solid on- soft work abnormal, fast Blink – soft upgrade PoE: Yellow Solid on- PoE work normally, Off- PoE doesn’t work, Blink - PoE overload 10/100/1000T RJ45 Interfaces (Port 1 to Port 24): 1000 LNK/ACT (Green) Blink - port connected with data transmission; Solid on- port connected without data transmission 100/1000Mbps SFP Interfaces (Port 22 to Port 24): Green Blink - port connected with data transmission; Solid on- port connected without data transmission EMC Surge Immunity: 4KV Per: IEC61000-4-5 ESD Protection: ESD Level 4 Per: IEC61000-4-2 EFT Level 4 Per: IEC61000-4-4 Layer2 Functions Port configuration Auto-negotiation Flow Control Port Mirror: TX/RX/BOTH; Many-to-1 monitor CPU Mirror Traffic statistics Link Aggregation Static link aggregation LACP (Dynamic Trunk/Static Trunk) Algorith based on Source/Destination MAC Algorithm based on Source/Destination IP MAC Table Aging Time Static MAC address Dynamic MAC address management VLAN 4094 Active VLANs 4094 VID 802.1Q Tag VLAN Port VLAN Protocol VLAN MAC VLAN Voice VLAN 802.1ad Q-in-Q tunneling Private VLAN (Protected port) GARP/GVRP ACL 256ACLs L2, L3 e L4 Time-based ACL IP ACL MAC ACL MAC-IP ACL User-Defined ACL ICMPv6 Spanning tree 802.1D Spanning Tree Protocol (STP) 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1s Multiple Spanning Tree Protocol (MSTP) Loop Guard Root Guard TC-BPDU Guard BPDU Guard BPDU Filter Ring Protection <20ms G.8032 ERPS Ring Fast Ring Multicast 256 groups IGMP v1/v2/v3 Snooping, Fast Leave MLD Snooping Multicast VLAN IGMP filter MVR Multicast Routing QOS 8 mapping IDs to 8 level priority queues CoS port-based CoS 802.1p-based CoS DSCP-based Scheduling algorithms SP, WRR, SP+WRR Storm Control (Broadcast, Multicast, Unknown Unicast) Bandwidth control per port SWRR, DWRR for Scheduling Flow Redirect Precedence TOS Rate Limiting (Ingress/Egress) Stri Priority Security Features Port Security MAC address filter ARP Association (Manual, ARP scanning, DHCP snooping) ARP Protection AAA DAI DoS (Denial of Service) Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type; 802.1x Authentication (port-based e MAC-based) TACACS/TACACS+ Authentication RADIUS Authentication DHCP Filter Guest VLAN SSLv2/SSLv3/TLSv1 SSHv1/SSHv2 Restriction of WEB access based on: IP Address, And. MAC and Port; Port Isolation Loopback detection Management SNMP v1/v2c/v3 with Full Private MIBs RMON 4 groups WEB (HTTP/HTTPS) CLI (Telnet, Console, SSHv1/v2) Firmware upgrade via console/web/TFTP Configuration Backup/Reload  Dual Firmware LLDP Configuration Export/Import CDP Aware OAM (IEEE802.3ah) CFM (IEEE802.1ag) sFlow Other Features DNS Client DHCP Relay DHCP Client DHCP Snooping DHCP Option 66 DHCP Option 67 DHCP Option 82 NTP/SNTP Client UPNP UDLD PoE management Total PoE power budget control Per port PoE function enable/disable PoE admin-mode control PoE port power feeding priority Per PoE port power limitation PD classification detection PD alive check PoE schedule Soft-reboot PoE Non-stop Maintenance Cable Diagnostics Ping SFP DDM (Digital Diagnostics Monitoring) Thermal protection System log (Local and Remote) Memory and CPU Monitoring Layer 3 functions Static Routing IPv4 Unicast: Static Routing(Software Base) IPv6 Unicast: Static Routing(Software Base) IPV6 IPv6 neighbor discovery (ND) Path maximum transmission unit (MTU) discovery Internet Control Message Protocol (ICMP) version 6 TCPv6/UDPv6 Ping6 Telnet(v6) Http/Https Interface IPV6 ACL IPV6 Dimension 440x290x44.5 mm Weight 4.5 kg Working Temperature -10 °C to 45 °C Storage Temperature -20 °C to 70 °C MTBF 50,000hrs

8-port 10/100/1000Mbit/s PoE Layer 2 Gigabit Ethernet Switch (8x 802.3af oder 4x 802.3at) Highlights: 8-Port 10/100/1000Mbit/s with full PoE PoE performance 4x 30 Watt (IEEE802.3at) or 8x 15,4 Watt (IEEE802.3af) internal power supply fanless Design   The ALL8808POE+ provides high power and data using Power over Ethernet (PoE) over Cat-5 cable. The Eight Gigabit Ethernet ports can be used for any 10/100/1000 Mbps link and eight of these ports can supply industry-standard IEEE 802.3af and four ports can supply IEEE 802.3at power.  ALL8808POE+ delivers PoE to any small business network that wants to simplify the installation of IP-Phone and IP-based surveillance cameras. Technical Details:   Network standards IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.ab 1000BaseT IEEE 802.3af PoE IEEE 802.3at PoE IEEE 802.3x Flow Control and Back-pressure IEEE 802.1p Class of Service Switch Features RJ-45 Ports: 8x 10/100/1000 Mbps MAC Address: 8K Buffer Memory: 2048K Bytes Jumbo Frames: 9.6K Transmission Method: Store and Forward Management N/A Power 100~240V/AC, 50~60Hz Power (without PoE) Max. 5 watt Power (with PoE) Max. 150 watt Case Metal housing 265 × 184 × 44 mm (W x D x H) Weight 0.95 kg Operating temperature 0 to 40? Humidity 10 to 90% (non-condensing) Certificates FCC Class A, CE    

ALLNET Switch full managed Layer2+ 10 Port • 8x GbE • PoE Budget 130W • 8x PoE at • 2x SFP • 19" • Fanless • JSON API • ALL-SG8610PMJ Highlights: 8-port 10/100/1000Mbit/s with full PoE support 2x SFP slots for optional MiniGBICS PoE power 4x a´ 30 watts (IEEE802.3at or 8x IEEE802.3af) LÜFTERLESS DESIGN with internal power supply Supports L2+ switching functions such as 802.1Q VLAN, mirroring, port isolation, IGMP snooping, DHCP snooping, LLDP, POE+ management, IP source guard, ARP inspection, ACLs etc. Support of Spanning Tree STP(802.1D) and RSTP(802.1W) and MSTP(802.1s). Support of extended management via WEB, CLI, TELNET, SSH, SNMP. Support for cable diagnostics and SFP DDM. Supports PoE management, such as PoE schedule, PoE PD Alive. Supports G.8032 quick ring protocol. Self-recovery time <20ms. Supports DDM, SFP digital diagnostics & monitoring Support of IPV4 and IPV6 functions for static routing Support of memory and CPU monitoring 4KV overvoltage protection, 6KV contact/8KV air protection PoE budget 130 W NEW: PoE & LAN JSON Java script notation API for ON/OFF via remote Product description: The ALL-SG8610PM is a fully managed Layer 2+ Gigabit PoE switch that features intelligent PoE capabilities to improve the availability of critical business applications. It offers IPv6/IPv4 management and an integrated L2+ Gigabit switching engine together with 8*10/100/1000BASE-T ports with 30 Watt 802.3at PoE+ and 2 Gigabit SFP slots. With a total power budget of up to 130 W for various types of PoE applications, it offers fast, secure and cost-effective Power over Ethernet network solutions for IP surveillance in small businesses and enterprises. The ALL-SG8610PM is programmed for advanced switch management features such as 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), Loop and BPDU Guard, IGMP Snooping and MLD Snooping. In addition, the Link Layer Discovery Protocol (LLDP) is included as a layer 2 protocol to determine basic information about neighbouring devices in the local broadcast domain.   Extensive PoE management function As a managed PoE switch for CCTV surveillance, wireless and VoIP networks, the ALL-SG8610PM has the following special PoE management functions:   PoE PD alive check Timed rebooting of the power supply PoE schedule Monitoring of PoE utilisation Soft reboot PoE non-stop Prioritisation of the PoE port feed-in Intelligent PD alive check for frozen PDs The ALL-SG8610PM industrial PoE switch with 24 ports can be configured to monitor the status of the connected PDs in real time. As soon as the PD stops working and responding, the ALL-SG8610PM restarts the power supply to the PoE port and gets the PD up and running again. In addition, reliability is significantly improved by the fact that the PoE port resets the PD power supply, reducing the administrative burden on the administrator. PoE schedule function for energy saving To protect the environment, the AALL-SG8610PM Switch Ethernet PoE can effectively control the power supply in addition to its ability to deliver high wattage. The PoE schedule function helps to enable or disable the PoE power supply for each PoE port during specific time intervals, and is a powerful feature that helps SMEs or enterprises to save power and money. Planned PD restart The intelligent PoE switch ALL-SG8610PM allows each of the connected PoE IP cameras or PoE wireless access points to be restarted at a specific time every week. This reduces the risk of the IP camera or AP crashing due to a buffer overflow. Redundant ring with fast recovery for critical network applications The ALL-SG8610PM supports redundant ring technology and has a strong, fast self-recovery capability to prevent interruptions and external intrusions. It integrates advanced ITU-T G.8032 ERPS technology, Spanning Tree Protocol (802.1s MSTP) and a redundant power supply system into the customer's industrial automation network to improve system reliability and uptime in harsh factory environments. In a given simple ring network, the data link recovery time can be as fast as 20 ms.   Strong layer 2 functions The ALL-SG8610PM Layer 2 Ethernet switch can be programmed for advanced Layer 2 switch management functions such as dynamic port link aggregation, 802.1Q tagged VLAN, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), QoS, bandwidth control, IGMP snooping and MLD snooping. By aggregating the supporting ports, the ALL-SG8610PM enables the operation of a high-speed trunk group that has multiple ports and also supports fail-over. Efficient and versatile management methods For efficient management, the ALL-SG8610PM is equipped with console, web and SNMP management interfaces. With the integrated web-based management interface, it offers a user-friendly, platform-independent management and configuration option. For text-based management, access is possible via Telnet and the console port. For standards-based monitoring and management software, it provides an SNMPv3 connection that encrypts the packet contents for secure remote management during each session. Intelligent PoE switch with SFP DDM function The ALL-SG8610PM supports the SFP DDM (Digital Diagnostic Monitor) function, which allows the network administrator to easily monitor real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias voltage and transceiver supply voltage.    JSON-Java Script Object Notation API With the JSON API, the ADMIN can create a special user and grant this user authorisation for JSON. We have focussed on 2 functions that we consider important.   PoE ON/OFF & LAN Port Enabled/Disabled (for switches with PoE function) LAN Port Enabled/Disabled (for switches without PoE) Technical data: Model ALL-SG8610PM Copper Ports 8-10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports Fibre ports 2x1G BASE-X SFP interfaces, supports 100M/1G Mbps dual mode PoE ports 1~8-802.3af/802.3at PoE Injector Ports Console ports 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1) Switch architecture Store-and-forward Switch Fabric 20 Gbps/non-blocking Throughput 14.88Mpps @64 bytes Address Table 8K entries Share Data Buffer 4 Mb Jumbo Frame 9600 bytes SDRAM 1Gb Flash memory 128Mb Flow control IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex Reset button >2 sec: Factory default and reset Power supply 100~240V AC, 50/60Hz, 4A (max.) Power consumption Max.150 watts/1122 BTU PoE standards IEEE 802.3af Power over Ethernet/PSE IEEE 802.3at Power over Ethernet Plus/PSE PoE power supply type Per port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af) Per port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at) PoE budget 130W LED Indicators Power: Green Solid on- power work normal, off- power disconnected System: Green Blink -work normally, solid on- soft work abnormal, fast Blink – soft upgrade PoE: Yellow Solid on- PoE work normally, Off- PoE doesn’t work, Blink - PoE overload 10/100/1000T RJ45 interfaces (Port 1 to Port 8): 1000 LNK/ACT (Green) Blink - port connected with data transmission; Solid on- port connected without data transmission 100/1000Mbps SFP interfaces (Port 9 to Port 10): Green Blink - port connected with data transmission; Solid on- port connected without data transmission EMC Surge Immunity: 4KV Per: IEC61000-4-5 ESD Protection: ESD Level 4 Per: IEC61000-4-2 EFT Level 4 Per: IEC61000-4-4 Layer2 Functions Port configuration Auto-negotiation flow control Port Mirror: TX/RX/BOTH; Many-to-1 monitor CPU Mirror Traffic statistics Link aggregation Static link aggregation LACP(Dynamic Trunk/Static Trunk) Algorithm based on Source/Destination MAC Algorithm based on Source/Destination IP MAC Table Aging Time Static MAC address Dynamic MAC address management VLAN 4094 Active VLANs 4094 VID 802.1Q Tag VLAN Port VLAN Protocol VLAN MAC VLAN Voice VLAN 802.1ad Q-in-Q tunnelling Private VLAN (Protected port) GARP/GVRP ACL 256ACLs L2, L3 e L4 Time-based ACL IP ACL MAC ACL MAC-IP ACL User-Defined ACL ICMPv6 Spanning tree 802.1D Spanning Tree Protocol (STP) 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1s Multiple Spanning Tree Protocol (MSTP) Loop Guard Root Guard TC-BPDU Guard BPDU Guard BPDU Filter Ring Protection <20ms G.8032 ERPS Ring Fast Ring Multicast 256 groups IGMP v1/v2/v3 Snooping, Fast Leave MLD Snooping Multicast VLAN IGMP filter MVR Multicast routing QOS 8 mapping IDs to 8 level priority queues CoS port-based CoS 802.1p-based CoS DSCP-based Scheduling algorithms SP, WRR, SP+WRR Storm Control (Broadcast, Multicast, Unknown Unicast) Bandwidth control per port SWRR, DWRR for Scheduling Flow Redirect Precedence TOS Rate limiting (Ingress/Egress) Stri Priority Security features Port Security MAC address filter ARP Association (Manual, ARP scanning, DHCP snooping) ARP protection AAA DAI DoS (Denial of Service) Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type; 802.1x Authentication (port-based e MAC-based) TACACS/TACACS+ Authentication RADIUS Authentication DHCP Filter Guest VLAN SSLv2/SSLv3/TLSv1 SSHv1/SSHv2 Restriction of WEB access based on: IP Address, And. MAC and Port; Port Isolation Loopback detection Management SNMP v1/v2c/v3 with Full Private MIBs RMON 4 groups WEB (HTTP/HTTPS) CLI (Telnet, Console, SSHv1/v2) Firmware upgrade via console/web/TFTP Configuration backup/reload  Dual firmware LLDP Configuration Export/Import                                CDP Aware OAM (IEEE802.3ah) CFM (IEEE802.1ag) sFlow Other features DNS Client DHCP Relay DHCP Client DHCP Snooping DHCP Option 66 DHCP Option 67 DHCP Option 82 NTP/SNTP Client UPNP UDLD PoE management Total PoE power budget control Per port PoE function enable/disable PoE admin-mode control PoE port power feeding priority Per PoE port power limitation PD classification detection PD alive check PoE schedule Soft-reboot PoE non-stop Maintenance Cable Diagnostics Ping SFP DDM (Digital Diagnostics Monitoring) Thermal protection System log (Local and Remote) Memory and CPU Monitoring Layer 3 functions Static routing IPv4 Unicast: Static Routing(Software Base) IPv6 Unicast: Static Routing(Software Base) IPV6 IPv6 neighbour discovery (ND) Path maximum transmission unit (MTU) discovery Internet Control Message Protocol (ICMP) version 6 TCPv6/UDPv6 Ping6 Telnet(v6) Http/Https Interface IPV6 ACL IPV6 Dimension 280x213x44.5mm Weight 2 kg Working Temperature -10°C to 45°C Storage Temperature -20°C to 70°C MTBF 50,000hrs

Ruckus Zubehör EU Power Adapter for ZoneFlex R560/ R650 / R720 / R730 / R750 / R850 Power Supply, DC Switching Mode, 48VDC 0.75A 36W, Inlet-C14, RoHS Power Cord, AR, RoHS, IEC 320, 6Ft Long

Zubehör Secure Mounting Bracket for ZoneFlex R320, R350, R510, R550, R560, R610, R650, R720, R730, R750, R760, R850

ICX 7150-48ZP Switch Z-Series, 16x 100/1000/2.5G PoH ports, 32x 10/100/1000 PoE+ ports, 2x 10G SFP+ and 6x 1G SFP uplink-ports upgradable to 8x 10G SFP+ with license. Basic L3 (static routing and RIP). 1 RPS20-E Power Supply, 1 Fan tray. 1,480 W PoE budget (with two power supplies)

Allnet Zubehör Mounting Bracket Kompatibel für Ruckus R320, R350, R510, R550, R560, R610, R650, R720, R750, R760, R850