Ubiquiti Wireless AP WIFI5 • AC1750 • 3x3 • Indoor • 1 GbE • Unifi • 5er Pack • UAP-AC-PRO-5

ALLNET PoE Injector Gigabit PoE & PoE+ (15,4W/30W) / plastic housing / "ALL0488v6   Highlights: PoE injector according to IEEE802.3af/at with max. power of 30W 2x RJ45 Gigabit Ports PoE Output 55VDC@30W Midspan PoE PIN's 4/5 (+) and 7/8(-) internal power supply unit compact design incl. 1.5m power cable with IEC-C5 to IEC-CEE7 protective contact cable NEW: Wall mounting capable Intelligent power supply via network without switch With the ALLNET ALL0488V6 Power over Ethernet Injector you can install your PoE-enabled IP devices such as WLAN access points, VoIP phones and much more absolutely independent of existing power sockets. For example, WLAN access points can be installed in the most ideal locations in a building without having to worry about power cabling. Switches that are not PoE-capable can be "retrofitted" with Power over Ethernet at a reasonable price, especially if only a few ports with PoE supply are required. Here, the ALL0488V6 saves the purchase of a PoE switch. The ALLNET ALL0488V6 supports the IEEE802.3af & IEEE802.3at standard with a maximum power of 30W Watt. The ALL0488V6 does not need to be configured. It has an RJ45 input socket and an RJ-45 output socket, which is used to connect the switch and terminal device to the PoE injector. The cable length here can be up to 100 meters between switch and terminal device in total, as is usual in Ethernet. Due to its compact design, the ALLNET ALL0488V6 can be installed very easy. It has an internal power supply and supplies the PoE voltage on pins 4/5 (+) and 7/8 (-). Technical Details: Element Specifikation Standards: IEEE802.3 10Base-T Ethernet IEEE802.3u 100Base-Tx Fast Ethernet IEEE802.3ab 1000Base-T Gigabit Ethernet Support terminal equipment with IEEE802.3af/at, PoE++ RoHS Compliance WEEE Compliance Ethernet Ports: 1x RJ45 10/100/1000 Mbps for connection to switch or hub 1x RJ45 10/100/1000 for connection to PoE end device PoE Output: PoE IEEE802.11af/at, Power pins: 4/5(+) 7/8(-) Power supply: 100 - 240VAC, internal power supply / Output: 55V/550mA incl. connection cable earth contact on IEC320-C5 "Kleeblat/Micky-Mouse" approx. 80cm length Power consumption: 30 Watt maximum with connected PoE end device AC Surge Protection: 1.0KV (5P/5N) L-N 1.2/50 (8/20) Tr/Th us 2.0KV (5P/5N) L-PE 1.2/50 (8/20) Tr/Th us N -PE Housing: Plastic housing Mounting: Wall-mounted Dimensions: length/width/height: 140 x 63 x 33 mm Environment: Operating Temperature: 0 ~ 40 °C Operating Humidity 10% ~ 90% (non-condensing) Storage Temperature: -20 ~ 90 °C Storage Humidity: 10% ~ 90% (non-condensing) EMI: FCC CFR47 Part 15 EN55024 EN55032 EMS: IEC61000-4-2(ESD) ± 6kV(contact), ±8kV(air) IEC61000-4-3(RS) 10V/m(80MHz~2GHz) IEC61000-4-4(EFT) Power Port: ±2kV; Data Port:±1kV IEC61000-4-5(Surge) Power Port:±1kV/DM, ±2kV/CM IEC61000-4-6(CS) 10V(150kHz~80MHz) Immunity: IEC60068-2-6(Vibration) IEC60068-2-27(Impact) IEC60068-2-32(Free Fall) Marks: CE; FCC

8-port 10/100/1000Mbit/s PoE Layer 2 Gigabit Ethernet Switch (8x 802.3af oder 4x 802.3at) Highlights: 8-Port 10/100/1000Mbit/s with full PoE PoE performance 4x 30 Watt (IEEE802.3at) or 8x 15,4 Watt (IEEE802.3af) internal power supply fanless Design   The ALL8808POE+ provides high power and data using Power over Ethernet (PoE) over Cat-5 cable. The Eight Gigabit Ethernet ports can be used for any 10/100/1000 Mbps link and eight of these ports can supply industry-standard IEEE 802.3af and four ports can supply IEEE 802.3at power.  ALL8808POE+ delivers PoE to any small business network that wants to simplify the installation of IP-Phone and IP-based surveillance cameras. Technical Details:   Network standards IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.ab 1000BaseT IEEE 802.3af PoE IEEE 802.3at PoE IEEE 802.3x Flow Control and Back-pressure IEEE 802.1p Class of Service Switch Features RJ-45 Ports: 8x 10/100/1000 Mbps MAC Address: 8K Buffer Memory: 2048K Bytes Jumbo Frames: 9.6K Transmission Method: Store and Forward Management N/A Power 100~240V/AC, 50~60Hz Power (without PoE) Max. 5 watt Power (with PoE) Max. 150 watt Case Metal housing 265 × 184 × 44 mm (W x D x H) Weight 0.95 kg Operating temperature 0 to 40? Humidity 10 to 90% (non-condensing) Certificates FCC Class A, CE    

ALLNET Switch full managed Layer2+ 10 Port • 8x GbE • PoE Budget 130W • 8x PoE at • 2x SFP • 19" • Fanless • JSON API • ALL-SG8610PMJ Highlights: 8-port 10/100/1000Mbit/s with full PoE support 2x SFP slots for optional MiniGBICS PoE power 4x a´ 30 watts (IEEE802.3at or 8x IEEE802.3af) LÜFTERLESS DESIGN with internal power supply Supports L2+ switching functions such as 802.1Q VLAN, mirroring, port isolation, IGMP snooping, DHCP snooping, LLDP, POE+ management, IP source guard, ARP inspection, ACLs etc. Support of Spanning Tree STP(802.1D) and RSTP(802.1W) and MSTP(802.1s). Support of extended management via WEB, CLI, TELNET, SSH, SNMP. Support for cable diagnostics and SFP DDM. Supports PoE management, such as PoE schedule, PoE PD Alive. Supports G.8032 quick ring protocol. Self-recovery time <20ms. Supports DDM, SFP digital diagnostics & monitoring Support of IPV4 and IPV6 functions for static routing Support of memory and CPU monitoring 4KV overvoltage protection, 6KV contact/8KV air protection PoE budget 130 W NEW: PoE & LAN JSON Java script notation API for ON/OFF via remote Product description: The ALL-SG8610PM is a fully managed Layer 2+ Gigabit PoE switch that features intelligent PoE capabilities to improve the availability of critical business applications. It offers IPv6/IPv4 management and an integrated L2+ Gigabit switching engine together with 8*10/100/1000BASE-T ports with 30 Watt 802.3at PoE+ and 2 Gigabit SFP slots. With a total power budget of up to 130 W for various types of PoE applications, it offers fast, secure and cost-effective Power over Ethernet network solutions for IP surveillance in small businesses and enterprises. The ALL-SG8610PM is programmed for advanced switch management features such as 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), Loop and BPDU Guard, IGMP Snooping and MLD Snooping. In addition, the Link Layer Discovery Protocol (LLDP) is included as a layer 2 protocol to determine basic information about neighbouring devices in the local broadcast domain.   Extensive PoE management function As a managed PoE switch for CCTV surveillance, wireless and VoIP networks, the ALL-SG8610PM has the following special PoE management functions:   PoE PD alive check Timed rebooting of the power supply PoE schedule Monitoring of PoE utilisation Soft reboot PoE non-stop Prioritisation of the PoE port feed-in Intelligent PD alive check for frozen PDs The ALL-SG8610PM industrial PoE switch with 24 ports can be configured to monitor the status of the connected PDs in real time. As soon as the PD stops working and responding, the ALL-SG8610PM restarts the power supply to the PoE port and gets the PD up and running again. In addition, reliability is significantly improved by the fact that the PoE port resets the PD power supply, reducing the administrative burden on the administrator. PoE schedule function for energy saving To protect the environment, the AALL-SG8610PM Switch Ethernet PoE can effectively control the power supply in addition to its ability to deliver high wattage. The PoE schedule function helps to enable or disable the PoE power supply for each PoE port during specific time intervals, and is a powerful feature that helps SMEs or enterprises to save power and money. Planned PD restart The intelligent PoE switch ALL-SG8610PM allows each of the connected PoE IP cameras or PoE wireless access points to be restarted at a specific time every week. This reduces the risk of the IP camera or AP crashing due to a buffer overflow. Redundant ring with fast recovery for critical network applications The ALL-SG8610PM supports redundant ring technology and has a strong, fast self-recovery capability to prevent interruptions and external intrusions. It integrates advanced ITU-T G.8032 ERPS technology, Spanning Tree Protocol (802.1s MSTP) and a redundant power supply system into the customer's industrial automation network to improve system reliability and uptime in harsh factory environments. In a given simple ring network, the data link recovery time can be as fast as 20 ms.   Strong layer 2 functions The ALL-SG8610PM Layer 2 Ethernet switch can be programmed for advanced Layer 2 switch management functions such as dynamic port link aggregation, 802.1Q tagged VLAN, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), QoS, bandwidth control, IGMP snooping and MLD snooping. By aggregating the supporting ports, the ALL-SG8610PM enables the operation of a high-speed trunk group that has multiple ports and also supports fail-over. Efficient and versatile management methods For efficient management, the ALL-SG8610PM is equipped with console, web and SNMP management interfaces. With the integrated web-based management interface, it offers a user-friendly, platform-independent management and configuration option. For text-based management, access is possible via Telnet and the console port. For standards-based monitoring and management software, it provides an SNMPv3 connection that encrypts the packet contents for secure remote management during each session. Intelligent PoE switch with SFP DDM function The ALL-SG8610PM supports the SFP DDM (Digital Diagnostic Monitor) function, which allows the network administrator to easily monitor real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias voltage and transceiver supply voltage.    JSON-Java Script Object Notation API With the JSON API, the ADMIN can create a special user and grant this user authorisation for JSON. We have focussed on 2 functions that we consider important.   PoE ON/OFF & LAN Port Enabled/Disabled (for switches with PoE function) LAN Port Enabled/Disabled (for switches without PoE) Technical data: Model ALL-SG8610PM Copper Ports 8-10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports Fibre ports 2x1G BASE-X SFP interfaces, supports 100M/1G Mbps dual mode PoE ports 1~8-802.3af/802.3at PoE Injector Ports Console ports 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1) Switch architecture Store-and-forward Switch Fabric 20 Gbps/non-blocking Throughput 14.88Mpps @64 bytes Address Table 8K entries Share Data Buffer 4 Mb Jumbo Frame 9600 bytes SDRAM 1Gb Flash memory 128Mb Flow control IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex Reset button >2 sec: Factory default and reset Power supply 100~240V AC, 50/60Hz, 4A (max.) Power consumption Max.150 watts/1122 BTU PoE standards IEEE 802.3af Power over Ethernet/PSE IEEE 802.3at Power over Ethernet Plus/PSE PoE power supply type Per port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af) Per port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at) PoE budget 130W LED Indicators Power: Green Solid on- power work normal, off- power disconnected System: Green Blink -work normally, solid on- soft work abnormal, fast Blink – soft upgrade PoE: Yellow Solid on- PoE work normally, Off- PoE doesn’t work, Blink - PoE overload 10/100/1000T RJ45 interfaces (Port 1 to Port 8): 1000 LNK/ACT (Green) Blink - port connected with data transmission; Solid on- port connected without data transmission 100/1000Mbps SFP interfaces (Port 9 to Port 10): Green Blink - port connected with data transmission; Solid on- port connected without data transmission EMC Surge Immunity: 4KV Per: IEC61000-4-5 ESD Protection: ESD Level 4 Per: IEC61000-4-2 EFT Level 4 Per: IEC61000-4-4 Layer2 Functions Port configuration Auto-negotiation flow control Port Mirror: TX/RX/BOTH; Many-to-1 monitor CPU Mirror Traffic statistics Link aggregation Static link aggregation LACP(Dynamic Trunk/Static Trunk) Algorithm based on Source/Destination MAC Algorithm based on Source/Destination IP MAC Table Aging Time Static MAC address Dynamic MAC address management VLAN 4094 Active VLANs 4094 VID 802.1Q Tag VLAN Port VLAN Protocol VLAN MAC VLAN Voice VLAN 802.1ad Q-in-Q tunnelling Private VLAN (Protected port) GARP/GVRP ACL 256ACLs L2, L3 e L4 Time-based ACL IP ACL MAC ACL MAC-IP ACL User-Defined ACL ICMPv6 Spanning tree 802.1D Spanning Tree Protocol (STP) 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1s Multiple Spanning Tree Protocol (MSTP) Loop Guard Root Guard TC-BPDU Guard BPDU Guard BPDU Filter Ring Protection <20ms G.8032 ERPS Ring Fast Ring Multicast 256 groups IGMP v1/v2/v3 Snooping, Fast Leave MLD Snooping Multicast VLAN IGMP filter MVR Multicast routing QOS 8 mapping IDs to 8 level priority queues CoS port-based CoS 802.1p-based CoS DSCP-based Scheduling algorithms SP, WRR, SP+WRR Storm Control (Broadcast, Multicast, Unknown Unicast) Bandwidth control per port SWRR, DWRR for Scheduling Flow Redirect Precedence TOS Rate limiting (Ingress/Egress) Stri Priority Security features Port Security MAC address filter ARP Association (Manual, ARP scanning, DHCP snooping) ARP protection AAA DAI DoS (Denial of Service) Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type; 802.1x Authentication (port-based e MAC-based) TACACS/TACACS+ Authentication RADIUS Authentication DHCP Filter Guest VLAN SSLv2/SSLv3/TLSv1 SSHv1/SSHv2 Restriction of WEB access based on: IP Address, And. MAC and Port; Port Isolation Loopback detection Management SNMP v1/v2c/v3 with Full Private MIBs RMON 4 groups WEB (HTTP/HTTPS) CLI (Telnet, Console, SSHv1/v2) Firmware upgrade via console/web/TFTP Configuration backup/reload  Dual firmware LLDP Configuration Export/Import                                CDP Aware OAM (IEEE802.3ah) CFM (IEEE802.1ag) sFlow Other features DNS Client DHCP Relay DHCP Client DHCP Snooping DHCP Option 66 DHCP Option 67 DHCP Option 82 NTP/SNTP Client UPNP UDLD PoE management Total PoE power budget control Per port PoE function enable/disable PoE admin-mode control PoE port power feeding priority Per PoE port power limitation PD classification detection PD alive check PoE schedule Soft-reboot PoE non-stop Maintenance Cable Diagnostics Ping SFP DDM (Digital Diagnostics Monitoring) Thermal protection System log (Local and Remote) Memory and CPU Monitoring Layer 3 functions Static routing IPv4 Unicast: Static Routing(Software Base) IPv6 Unicast: Static Routing(Software Base) IPV6 IPv6 neighbour discovery (ND) Path maximum transmission unit (MTU) discovery Internet Control Message Protocol (ICMP) version 6 TCPv6/UDPv6 Ping6 Telnet(v6) Http/Https Interface IPV6 ACL IPV6 Dimension 280x213x44.5mm Weight 2 kg Working Temperature -10°C to 45°C Storage Temperature -20°C to 70°C MTBF 50,000hrs

Ubiquiti POE Injector, 48VDC, 24W (RocketTi, UAP-Pro) Modell GP-D480-050G 48V 0,5A Passives PoE, nur mit geeigneten Endgeräten betreiben!

PoE Injector, 802.3AF Ubiquiti PoE Adapters provide a variety of features to help protect your PoE devices: Surge protection Clamping protection Maximum surge discharge Peak pulse current AC cable with earth ground Electrostatic discharge (ESD) is the leading cause for outdoor device failures. You can effectively protect against ESD damage using a grounded Ubiquiti PoE Adapter, TOUGHCableTM, and TOUGHCable Connectors.

Ubiquiti POE Injector, 24VDC, 12W Passives PoE, nur mit geeigneten Endgeräten betreiben!

Ubiquiti 24 V DC PoE Adapters providing a variety of features to help protect your PoE devices. Surge and clamping protection Maximum surge discharge Peak pulse current AC cable with earth ground     Technical Specifications POE-24-7W-G-WH (Low-Power) Dimensions 72 x 45 x 33 mm (2.84 x 1.75 x 1.33") Weight 72.1g (2.54 oz) Output Voltage 24VDC @ 0.3A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.3A @ 120VAC, 0.2A @240VAC Inrush Current <40A Peak @ 120VAC, <70A Peak @ 230VAC Efficiency 80+% Output Ripple 1% Max. Switching Frequency 65 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering – Operating Temperature 0 to 40°C (32 to 104°F) Storage Temperature -30 to 70°C (-22 to 158°F) Operating Humidity 35 to 95% Non-Condensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pf data Response Time <1 ns Certifications CE, FCC, IC, UL POE-24-12W-G (Mid-Power) Dimensions 87 x 44 x 29 mm (3.43 x 1.73 x 1.14") Weight 99.4 g (3.51 oz) Output Voltage 24VDC @ 0.5A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.3A @ 120VAC, 0.2A @ 240VAC Inrush Current <30A Peak @ 120VAC, <60A Peak @ 230VAC Efficiency 75+% Output Ripple 1% Max. Switching Frequency 50 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering - Operating Temperature 0 to 40° C (32 to 104° F) Storage Temperature -30 to 70°C (-22 to 158° F) Operating Humidity 35 to 95% Noncondensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pF data Response Time <1 ns Certifications CE, FCC, IC, UL POE-24-24W-G (Hi-Power) Dimensions 88 x 57 x 33 mm (3.47 x 2.24 x 1.30") Weight 158.5 g (5.59 oz) Output Voltage 24VDC @ 1.0A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.6A @ 120VAC, 0.4A @ 240VAC Inrush Current <60A Peak @ 120VAC, <120A Peak @ 230VAC Efficiency 80+% Output Ripple 1% Max. Switching Frequency 65 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering - Operating Temperature 0 to 40° C (32 to 104° F) Storage Temperature -30 to 70°C (-22 to 158° F) Operating Humidity 35 to 95% Noncondensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pF data Response Time <1 ns Certifications CE, FCC, IC, UL

PoE Injector, 24VDC, 12W, 5-Pack Passives PoE, nur mit geeigneten Endgeräten betreiben!

Ubiquiti 24 V DC PoE Adapters providing a variety of features to help protect your PoE devices. Surge and clamping protection Maximum surge discharge Peak pulse current AC cable with earth ground     Technical Specifications POE-24-7W-G-WH (Low-Power) Dimensions 72 x 45 x 33 mm (2.84 x 1.75 x 1.33") Weight 72.1g (2.54 oz) Output Voltage 24VDC @ 0.3A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.3A @ 120VAC, 0.2A @240VAC Inrush Current <40A Peak @ 120VAC, <70A Peak @ 230VAC Efficiency 80+% Output Ripple 1% Max. Switching Frequency 65 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering – Operating Temperature 0 to 40°C (32 to 104°F) Storage Temperature -30 to 70°C (-22 to 158°F) Operating Humidity 35 to 95% Non-Condensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pf data Response Time <1 ns Certifications CE, FCC, IC, UL POE-24-12W-G (Mid-Power) Dimensions 87 x 44 x 29 mm (3.43 x 1.73 x 1.14") Weight 99.4 g (3.51 oz) Output Voltage 24VDC @ 0.5A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.3A @ 120VAC, 0.2A @ 240VAC Inrush Current <30A Peak @ 120VAC, <60A Peak @ 230VAC Efficiency 75+% Output Ripple 1% Max. Switching Frequency 50 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering - Operating Temperature 0 to 40° C (32 to 104° F) Storage Temperature -30 to 70°C (-22 to 158° F) Operating Humidity 35 to 95% Noncondensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pF data Response Time <1 ns Certifications CE, FCC, IC, UL POE-24-24W-G (Hi-Power) Dimensions 88 x 57 x 33 mm (3.47 x 2.24 x 1.30") Weight 158.5 g (5.59 oz) Output Voltage 24VDC @ 1.0A LAN Activity Indicator No Gigabit LAN Port Yes Remote Reset Capability Yes Reset Button Yes Rated Voltage 100-240VAC @ 50/60Hz Input Current 0.6A @ 120VAC, 0.4A @ 240VAC Inrush Current <60A Peak @ 120VAC, <120A Peak @ 230VAC Efficiency 80+% Output Ripple 1% Max. Switching Frequency 65 kHz Line Regulation ≤ 3% Load Regulation ≤ 5% 2-Pair Powering Pins 4, 5 (+) and Pins 7, 8 (-) 4-Pair Powering - Operating Temperature 0 to 40° C (32 to 104° F) Storage Temperature -30 to 70°C (-22 to 158° F) Operating Humidity 35 to 95% Noncondensing AC Connector IEC-320 C6 Data IN / PoE RJ45 Shielded Socket Surge Protection Difference and Common Mode Clamping Protection 11V Data, 60V Power Max. Surge Discharge 1500A (8/20 μs) Power Peak Pulse Current 36A (10/1000 μs) Data Shunt Capacitance <5 pF data Response Time <1 ns Certifications CE, FCC, IC, UL