Highlights: Frequency range: 2 - 199 MHz Network standard: G.hn Hardware encryption: AES 128-bit Quality of Service: VLAN/TOS/Packet Classifier/ Gross data rate: 2000 Mbps max. Net data rate: 1700 Mbps max. incl. power supply for the optional EOC sockets 200MHz max. EOC sockets can be operated per module in the chassis The G.hn module is used to extend an existing AMP ALL-GHN108-200 distribution amplifier in conjunction with EOC 200 flush-mounted boxes. Up to eight G.hn modules can be installed per distribution amplifier. Only G.hn modules of the same type (200MHz) can be installed per distribution amplifier. The G.hn plug-in module enables an additional coaxial line to be integrated, which is available in the line with EOC 100MHz flush-mounted sockets for picking up network data and/or DVB-C signals. This is also known as DVB-C coexistence. ATTENTION: This is only the 200MHz g.hn module, the chassis/amplifier Art. 221624 is also required. see accessories  

The EOC 200 (ALL-GHN108S-200-UP-Dose) is an in-wall socket which supports the simultaneous transmission of Internet and Cable TV on an existing coax cable network. The installation of the in-wall socket is adding an internet connection to the existing use of cable TV on the same coax cable. It contains an integrated Gbit LAN interface and a C pass-through socket. Internet/Network data can be utilized via the Gbit Ethernet connection. The coaxial socket provides a broadband cable signal in the range of 240 MHz to 860 MHz. The TV signal gets decoupled via the coaxial socket, whereas network data is transmitted via the RJ45 socket. Interconnection of individual in-wall sockets is done automatically. The first in-wall socket is capable of supplying up to another 5 in-wall sockets. (Part No: 221626 ALL-GHN108S-200-UP-Dose  or Part No: 221627 ALL-GHN108S-200-WIFI)       The EOC 200 can be powered via remote supply by an ALL-GHN108M-Coax-200 (Amplifier), or with a 24 V/1 A power supply. Therefor it can supply four subsequent EOC 200. The EOC 200 can be installed in a single flush-mounted box, as well as in a multiple flush-mounted box. (Part No: 221626 ALL-GHN108S-200-UP-Dose  or Part No: 221627 ALL-GHN108S-200-WIFI)    Each EOC 200 can exchange data with any other flush-mounted box. (Part No: 221626 ALL-GHN108S-200-UP-Dose  or Part No: 221627 ALL-GHN108S-200-WIFI)    Video - Wiring and connection EOC in-wall socket to ALL-GHN108M-Coax-200 Amplifier Recommended application: Building upgrade with Gigabit Ethernet with existing coaxial cabling and limited budget. Home users Small company networks Hotels Hospitals Sanatoriums Retirement homes Renovation of old buildings Comparison of the Transmission Standard Standard G.Hn via COAX WLAN Powerline DOCSIS 3.0/3.1 over coax Net data rate 1,5 Gbit 240 Mbit - Wi-Fi 42 600 Mbit - Wi-Fi 52 800 Mbit - Wi-Fi 62 400 Mbit Powerline AV12002 400 Mbit Powerline AV20002 1600 Mbit/s download3 240 Mbit/s upload3 Acquisition cost medium Wi-Fi4 devices cheap Wi-Fi5 devices medium Wi-Fi6 devices expensive AV1200 devices cheap AV2000 devices medium high requires DOCSIS - CMTS server Power consumption up to 4W/GBit 6 W/GBit Access point included up to 6 W/GBit >8 W/GBit server included Susceptibility to interference not susceptible to yes, by many users yes, by electrical consumers not susceptible to Eavesdropping security yes WPA3 yes WPA2 no yes yes Visual impact small disappears in the wall medium router stands around large protrudes from the wall socket medium modem stands around 2 Source: https://de.wikipedia.org/wiki/Datendurchsatz 3 Source: https://de.wikipedia.org/wiki/Data_Over_Cable_Service_Interface_Specification Technical Details: C-throughput in-wall socket Can be integrated into single outlets and multiple outlets Frequency range 2 – 199 MHz Network standard: G.Hn Data rate Gross: 2000 Mbps Data rate Net: 1700 Mbps Attenuation 300 – 860 MHz: -2 dB (16 db coupling) Attenuation 300 – 860 MHz: -3 dB (10 db coupling) Coupling: 16 dB (other values on request) Hardware encryption : AES 128-bit Quality of Service: VLAN/TOS/Packet Classifier/Virtually perfect transmission with IPTV Remote service: TR-069 remote management (option) Only suitable for DVB-C wiring Satellite wiring is not supported   Power Consumption EOC 2000 Power Consumption 50 Mbit/s 2.06 Watt 100 Mbit/s 2.27 Watt 200 Mbit/s 2.47 Watt 300 Mbit/s 2.68 Watt 400 Mbit/s 2.81 Watt 500 Mbit/s 2.90 Watt 800 Mbit/s 3.09 Watt 1000 Mbit/s 3.15 Watt

The EOC WLAN is an in-wall socket which supports the simultaneous transmission of Internet and Cable TV on an existing coax cable network. The EOC WLAN in-wall socket is a "C"able pass-through socket with 2 antennas (2T2R) and integrated 2.4 GHz WiFi (Wi-Fi 4 2x2 802.11n). The coax socket provides a broadband cable signal in the range of 108 - 860 MHz, which can be used with a standard receiver. The TV signal is provided via the TV socket, the network dates are transmitted via WLAN. Interconnection of individual in-wall sockets is done automatically. The EOC WLAN is being powered via remote supply by an ALL-GHN108M-Coax-200  . Therefore, it can supply four subsequent EOC 100 and/or EOC 200 and/or EOC WLAN. The EOC WLAN can be installed in a single flush-mounted box as well as in a multiple flush-mounted box. Each EOC WLAN can exchange data with any other flush-mounted box. Recommended application: Building upgrade with gigabit Ethernet with existing coaxial cabling and on a limited budget. Home users Small company networks Hotels Hospitals Sanatoriums Retirement homes Renovation of old buildings Coax C-throughput in-wall socket Can be integrated into single outlets and multiple outlets Frequency range 2 – 199 MHz Network standard: G.Hn Data rate Gross: 2000 Mbps Data rate Net: 1700 Mbps Attenuation 300 – 860 MHz: -2 dB (16 db coupling) Attenuation 300 – 860 MHz: -3 dB (10 db coupling) Coupling: 10 db or 16 dB Hardware encryption : AES 128-bit Quality of Service: VLAN/TOS/Packet Classifier/Virtually perfect transmission with IPTV Remote service: TR-069 remote management (option) Only suitable for DVB-C wiring Satellite wiring is not supported     Technischen Daten: Software: openWRT 21.02.0 CPU: MIPS24KEc 580 MHz RAM: 64 MB RAM Flash: 32 MB Crypto: AES 128/256 Wi-Fi4: Datenrate 2x 150 Mbit/s (brutto) 2x2 802.11n Freqency: 2.4 GHz Antenna: 2T2R

ALLNET Switch full managed Layer2+ 10 Port • 8x GbE • PoE Budget 130W • 8x PoE at • 2x SFP • 19" • Fanless • JSON API • ALL-SG8610PMJ Highlights: 8-port 10/100/1000Mbit/s with full PoE support 2x SFP slots for optional MiniGBICS PoE power 4x a´ 30 watts (IEEE802.3at or 8x IEEE802.3af) LÜFTERLESS DESIGN with internal power supply Supports L2+ switching functions such as 802.1Q VLAN, mirroring, port isolation, IGMP snooping, DHCP snooping, LLDP, POE+ management, IP source guard, ARP inspection, ACLs etc. Support of Spanning Tree STP(802.1D) and RSTP(802.1W) and MSTP(802.1s). Support of extended management via WEB, CLI, TELNET, SSH, SNMP. Support for cable diagnostics and SFP DDM. Supports PoE management, such as PoE schedule, PoE PD Alive. Supports G.8032 quick ring protocol. Self-recovery time <20ms. Supports DDM, SFP digital diagnostics & monitoring Support of IPV4 and IPV6 functions for static routing Support of memory and CPU monitoring 4KV overvoltage protection, 6KV contact/8KV air protection PoE budget 130 W NEW: PoE & LAN JSON Java script notation API for ON/OFF via remote Product description: The ALL-SG8610PM is a fully managed Layer 2+ Gigabit PoE switch that features intelligent PoE capabilities to improve the availability of critical business applications. It offers IPv6/IPv4 management and an integrated L2+ Gigabit switching engine together with 8*10/100/1000BASE-T ports with 30 Watt 802.3at PoE+ and 2 Gigabit SFP slots. With a total power budget of up to 130 W for various types of PoE applications, it offers fast, secure and cost-effective Power over Ethernet network solutions for IP surveillance in small businesses and enterprises. The ALL-SG8610PM is programmed for advanced switch management features such as 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree Protocol (MSTP), Loop and BPDU Guard, IGMP Snooping and MLD Snooping. In addition, the Link Layer Discovery Protocol (LLDP) is included as a layer 2 protocol to determine basic information about neighbouring devices in the local broadcast domain.   Extensive PoE management function As a managed PoE switch for CCTV surveillance, wireless and VoIP networks, the ALL-SG8610PM has the following special PoE management functions:   PoE PD alive check Timed rebooting of the power supply PoE schedule Monitoring of PoE utilisation Soft reboot PoE non-stop Prioritisation of the PoE port feed-in Intelligent PD alive check for frozen PDs The ALL-SG8610PM industrial PoE switch with 24 ports can be configured to monitor the status of the connected PDs in real time. As soon as the PD stops working and responding, the ALL-SG8610PM restarts the power supply to the PoE port and gets the PD up and running again. In addition, reliability is significantly improved by the fact that the PoE port resets the PD power supply, reducing the administrative burden on the administrator. PoE schedule function for energy saving To protect the environment, the AALL-SG8610PM Switch Ethernet PoE can effectively control the power supply in addition to its ability to deliver high wattage. The PoE schedule function helps to enable or disable the PoE power supply for each PoE port during specific time intervals, and is a powerful feature that helps SMEs or enterprises to save power and money. Planned PD restart The intelligent PoE switch ALL-SG8610PM allows each of the connected PoE IP cameras or PoE wireless access points to be restarted at a specific time every week. This reduces the risk of the IP camera or AP crashing due to a buffer overflow. Redundant ring with fast recovery for critical network applications The ALL-SG8610PM supports redundant ring technology and has a strong, fast self-recovery capability to prevent interruptions and external intrusions. It integrates advanced ITU-T G.8032 ERPS technology, Spanning Tree Protocol (802.1s MSTP) and a redundant power supply system into the customer's industrial automation network to improve system reliability and uptime in harsh factory environments. In a given simple ring network, the data link recovery time can be as fast as 20 ms.   Strong layer 2 functions The ALL-SG8610PM Layer 2 Ethernet switch can be programmed for advanced Layer 2 switch management functions such as dynamic port link aggregation, 802.1Q tagged VLAN, Q-in-Q VLAN, private VLAN, Multiple Spanning Tree Protocol (MSTP), QoS, bandwidth control, IGMP snooping and MLD snooping. By aggregating the supporting ports, the ALL-SG8610PM enables the operation of a high-speed trunk group that has multiple ports and also supports fail-over. Efficient and versatile management methods For efficient management, the ALL-SG8610PM is equipped with console, web and SNMP management interfaces. With the integrated web-based management interface, it offers a user-friendly, platform-independent management and configuration option. For text-based management, access is possible via Telnet and the console port. For standards-based monitoring and management software, it provides an SNMPv3 connection that encrypts the packet contents for secure remote management during each session. Intelligent PoE switch with SFP DDM function The ALL-SG8610PM supports the SFP DDM (Digital Diagnostic Monitor) function, which allows the network administrator to easily monitor real-time parameters of the SFP transceivers, such as optical output power, optical input power, temperature, laser bias voltage and transceiver supply voltage.    JSON-Java Script Object Notation API With the JSON API, the ADMIN can create a special user and grant this user authorisation for JSON. We have focussed on 2 functions that we consider important.   PoE ON/OFF & LAN Port Enabled/Disabled (for switches with PoE function) LAN Port Enabled/Disabled (for switches without PoE) Technical data: Model ALL-SG8610PM Copper Ports 8-10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports Fibre ports 2x1G BASE-X SFP interfaces, supports 100M/1G Mbps dual mode PoE ports 1~8-802.3af/802.3at PoE Injector Ports Console ports 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1) Switch architecture Store-and-forward Switch Fabric 20 Gbps/non-blocking Throughput 14.88Mpps @64 bytes Address Table 8K entries Share Data Buffer 4 Mb Jumbo Frame 9600 bytes SDRAM 1Gb Flash memory 128Mb Flow control IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex Reset button >2 sec: Factory default and reset Power supply 100~240V AC, 50/60Hz, 4A (max.) Power consumption Max.150 watts/1122 BTU PoE standards IEEE 802.3af Power over Ethernet/PSE IEEE 802.3at Power over Ethernet Plus/PSE PoE power supply type Per port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af) Per port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at) PoE budget 130W LED Indicators Power: Green Solid on- power work normal, off- power disconnected System: Green Blink -work normally, solid on- soft work abnormal, fast Blink – soft upgrade PoE: Yellow Solid on- PoE work normally, Off- PoE doesn’t work, Blink - PoE overload 10/100/1000T RJ45 interfaces (Port 1 to Port 8): 1000 LNK/ACT (Green) Blink - port connected with data transmission; Solid on- port connected without data transmission 100/1000Mbps SFP interfaces (Port 9 to Port 10): Green Blink - port connected with data transmission; Solid on- port connected without data transmission EMC Surge Immunity: 4KV Per: IEC61000-4-5 ESD Protection: ESD Level 4 Per: IEC61000-4-2 EFT Level 4 Per: IEC61000-4-4 Layer2 Functions Port configuration Auto-negotiation flow control Port Mirror: TX/RX/BOTH; Many-to-1 monitor CPU Mirror Traffic statistics Link aggregation Static link aggregation LACP(Dynamic Trunk/Static Trunk) Algorithm based on Source/Destination MAC Algorithm based on Source/Destination IP MAC Table Aging Time Static MAC address Dynamic MAC address management VLAN 4094 Active VLANs 4094 VID 802.1Q Tag VLAN Port VLAN Protocol VLAN MAC VLAN Voice VLAN 802.1ad Q-in-Q tunnelling Private VLAN (Protected port) GARP/GVRP ACL 256ACLs L2, L3 e L4 Time-based ACL IP ACL MAC ACL MAC-IP ACL User-Defined ACL ICMPv6 Spanning tree 802.1D Spanning Tree Protocol (STP) 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1s Multiple Spanning Tree Protocol (MSTP) Loop Guard Root Guard TC-BPDU Guard BPDU Guard BPDU Filter Ring Protection <20ms G.8032 ERPS Ring Fast Ring Multicast 256 groups IGMP v1/v2/v3 Snooping, Fast Leave MLD Snooping Multicast VLAN IGMP filter MVR Multicast routing QOS 8 mapping IDs to 8 level priority queues CoS port-based CoS 802.1p-based CoS DSCP-based Scheduling algorithms SP, WRR, SP+WRR Storm Control (Broadcast, Multicast, Unknown Unicast) Bandwidth control per port SWRR, DWRR for Scheduling Flow Redirect Precedence TOS Rate limiting (Ingress/Egress) Stri Priority Security features Port Security MAC address filter ARP Association (Manual, ARP scanning, DHCP snooping) ARP protection AAA DAI DoS (Denial of Service) Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type; 802.1x Authentication (port-based e MAC-based) TACACS/TACACS+ Authentication RADIUS Authentication DHCP Filter Guest VLAN SSLv2/SSLv3/TLSv1 SSHv1/SSHv2 Restriction of WEB access based on: IP Address, And. MAC and Port; Port Isolation Loopback detection Management SNMP v1/v2c/v3 with Full Private MIBs RMON 4 groups WEB (HTTP/HTTPS) CLI (Telnet, Console, SSHv1/v2) Firmware upgrade via console/web/TFTP Configuration backup/reload  Dual firmware LLDP Configuration Export/Import                                CDP Aware OAM (IEEE802.3ah) CFM (IEEE802.1ag) sFlow Other features DNS Client DHCP Relay DHCP Client DHCP Snooping DHCP Option 66 DHCP Option 67 DHCP Option 82 NTP/SNTP Client UPNP UDLD PoE management Total PoE power budget control Per port PoE function enable/disable PoE admin-mode control PoE port power feeding priority Per PoE port power limitation PD classification detection PD alive check PoE schedule Soft-reboot PoE non-stop Maintenance Cable Diagnostics Ping SFP DDM (Digital Diagnostics Monitoring) Thermal protection System log (Local and Remote) Memory and CPU Monitoring Layer 3 functions Static routing IPv4 Unicast: Static Routing(Software Base) IPv6 Unicast: Static Routing(Software Base) IPV6 IPv6 neighbour discovery (ND) Path maximum transmission unit (MTU) discovery Internet Control Message Protocol (ICMP) version 6 TCPv6/UDPv6 Ping6 Telnet(v6) Http/Https Interface IPV6 ACL IPV6 Dimension 280x213x44.5mm Weight 2 kg Working Temperature -10°C to 45°C Storage Temperature -20°C to 70°C MTBF 50,000hrs

Highlights:  16 port Gigabit Layer2+ full managed switch architecture.  Supports NWay protocol for speed (10/100/1000Mbps) and duplex mode (half/full) auto-detection  Supports back-pressure (half duplex), flow control (IEEE 802.3x and IEEE 802.3az Energy Efficient Ethernet)  VLAN 4K Static / Port-Based / Tagged Based / Protocol / Voice VLAN / 802.1ad Q-in-Q  Link Aggregation static link / LACP / Algorithm MAC based or IP based  IGMP Snooping 256 groups IGMP v1/v2/v3, Fast Leave  QoS (QoS>QoS multi-label, queue config, QoS mapping)  Stormcontrol  Total fanless, no more annoying noises...  19 "inch angle or wall/table mounting possible ALL-SG8618M is a 16* 10/100/1000M RJ45 ports and 2*100/1000M SFP fiber slot ports L2+ managed Ethernet fiber switch , built-in 35W power supply. Support 1U/19 inch rack installation.It is programmed for advanced switch management functions such as 802.1Q VLAN and Q-in-Q VLAN, Multiple Spanning Tree protocol (MSTP), loop and BPDU guard, IGMP snooping, and MLD snooping. Also, the Link Layer Discovery Protocol (LLDP) is the Layer 2 protocol included to help discover basic information about neighboring devices on the local broadcast domain. It provides a quick, safe and cost-effective Ethernet network solution for small businesses and enterprises. Solution for IPv6 Networking With the IPv6/IPv4 dual stack and other management functions, ALL-SG8618M is the best choice for IP CCTV surveillance, VoIP and wireless solution providers to develop the IPv6 network. Meanwhile they help the SMBs to upgrade their network infrastructures to the IPv6 era without any extra investment. Robust Layer 2 Features ALL-SG8618M can be programmed for advanced Ethernet fiber switch management functions, such as port aggregation, Q-in-Q VLAN, Spanning Tree Protocol, QoS, bandwidth control, ERPS IGMP/MLD snooping etc. The ALL-SG86xx series allows the operation of a high-speed trunk combining multiple ports. Powerful Security Functions ALL-SG8618M provides a comprehensive access control list (ACL) for enforcing security to the edge. It can be used to restrict to network access by denying packets based on source and destination IP address, TCP/UDP port number or defined typical network applications. Its protection mechanism also comprises 802.1x Port-based and MAC-based user and device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user privacy. Enhanced Security and Traffic Control ALL-SG8618M supports DHCP Snooping, IP Source Guard and Dynamic ARP Inspection functions to prevent IP snooping from attack and discard ARP packets with invalid MAC address. The network administrator can now construct highly-secure corporate networks with considerably less time and effort than before. User-friendly Secure Management For efficient management, ALL-SG8618M is a managed switch, equipped with console, web and SNMP management interfaces. With management interface, ALL-SG8618M offers an easy-to-use, platform independent management and configuration facility. ALL-SG8618M supports SNMP and it can be managed via any management software based on the standard SNMP v1 or v2 Protocol. Meanwhile ALL-SG8618M offers Cisco-like command via Telnet or console port and customer doesn’t need to learn new command from these switches. Moreover,ALL-SG8618M offers the remotely secure management by supporting SSH, SSL and SNMP v3 connection where the packet content can be encrypted at each session. Intelligent SFP DDM Function ALL-SG8618M support SFP-DDM (Digital Diagnostic Monitor) function that greatly helps network administrator to easily monitor real-time parameters of the SFP and SFP+ transceivers, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage.  Fast Recovery Redundant Ring for Critical Network Applications The ALL-SG8618M supports redundant ring technology and features strong, rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS technology, Spanning Tree Protocol (802.1s MSTP), and redundant power input system into customer’s industrial automation network to enhance system reliability and uptime in harsh factory environments. In a certain simple Ring network, the recovery time of data link can be as fast as 20ms. Technical Details:   Model ALL-SG8618M Copper Ports 16 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports Fiber Ports 2-100/1000BASE-X SFP interfaces, supports 100/1000Mbps dual mode Console Ports 1 x RS-232-to-RJ45 serial port (115200, 8, N, 1) Switch Architecture Store-and-Forward Switch Fabric 36Gbps/non-blocking Throughput 23.819Mpps @64 bytes Address Table 8K entries Share Data Buffer 4.0 Mb Jumbo Frame 9600 Bytes SDRAM 1Gb Flash Memory 128Mb Flow Control IEEE 802.3x pause frame for full-duplex,Back pressure for half-duplex Reset Button > 2 sec: Factory default and reset Power Supply 100~240V AC, 50/60Hz, 4A (max.) Power Consumption 12V, 45watts/1122 BTU LED Indicators Power: Green Solid on- power work normal, off- power disconnected System: Green Blink-work normally, solid on- soft work abnormal, fast Blink- soft upgrade 10/100/1000T RJ45 Interfaces (Port 1 to Port 16): 1000 LNK/ACT (Green), 10/100 LNK/ACT (yellow) Blink- port connected with data transmission; Solid on- port connected without data transmission 100/1000Mbps SFP Interfaces (Port 17 to Port 18): Green Blink- port connected with data transmission; Solid on- port connected without data transmission EMC Surge Immunity: IEC61000-4-5 ESD Protection: ESD IEC61000-4-2: EFT IEC61000-4-4 Dimension 440x240x44.5mm Weight 3.2kg Working Temperature -10°C to 45°C Storage Temperature -20°C to 70°C MTBF 50,000hrs Layer 2 functions Port configuration Auto-negotiation Flow Control Port Mirror: TX/RX/BOTH; Many-to-1 monitor CPU Mirror Traffic statistics Link Aggregation Static link aggregation LACP(Dynamic Trunk/Static Trunk) Algorith based on Source/Destination MAC Algorithm based on Source/Destination IP MAC Table Aging Time Static MAC address Dynamic MAC address management VLAN 4094 Active VLANs 4094 VID 802.1Q Tag VLAN Port VLAN Protocol VLAN MAC VLAN Voice VLAN 802.1ad Q-in-Q tunneling Private VLAN (Protected port) GARP/GVRP ACL 256ACLs L2, L3 e L4 Time-based ACL IP ACL MAC ACL MAC-IP ACL User-Defined ACL ICMPv6 Spanning tree 802.1D Spanning Tree Protocol (STP) 802.1w Rapid Spanning Tree Protocol (RSTP) 802.1s Multiple Spanning Tree Protocol (MSTP) Loop Guard Root Guard TC-BPDU Guard BPDU Guard BPDU Filter Ring Protection <20ms G.8032 ERPS Ring Fast Ring Multicast 256 groups IGMP v1/v2/v3 Snooping, Fast Leave MLD Snooping Multicast VLAN IGMP filter MVR Multicast Routing QOS 8 mapping IDs to 8 level priority queues CoS port-based CoS 802.1p-based CoS DSCP-based Scheduling algorithms SP, WRR, SP+WRR Storm Control (Broadcast, Multicast, Unknown Unicast) Bandwidth control per port SWRR, DWRR for Scheduling Flow Redirect Precedence TOS Rate Limiting(Ingress/Egress) Stri Priority Security Features Port Security MAC address filter ARP Association (Manual, ARP scanning, DHCP snooping) ARP Protection AAA DAI DoS (Denial of Service) Classification of packages based on: End.MAC, IP End, TCP / UDP Ports, Protocol Type; 802.1x Authentication (port-based e MAC-based) TACACS/TACACS+ Authentication RADIUS Authentication DHCP Filter Guest VLAN SSLv2/SSLv3/TLSv1 SSHv1/SSHv2 Restriction of WEB access based on: IP Address, And. MAC and Port; Port Isolation Loopback detection Management SNMP v1/v2c/v3 with Full Private MIBs RMON 4 groups WEB (HTTP/HTTPS) CLI (Telnet, Console, SSHv1/v2) Firmware upgrade via console/web/TFTP Configuration Backup/Reload Dual Firmware LLDP Configuration Export/Import CDP Aware OAM (IEEE802.3ah) CFM (IEEE802.1ag) SFlow Telnet client Other Features DNS Client DHCP Relay DHCP Client DHCP Snooping DHCP Option 66 DHCP Option 67 DHCP Option 82 NTP/SNTP Client UPNP UDLD Maintenance Cable Diagnostics Ping SFP DDM (Digital Diagnostics Monitoring) Thermal protection System log (Local and Remote) Memory and CPU Monitoring Tracert /Tracert 6  Layer 3 functions Static Routing IPv4 Unicast: Static Routing(Software Base) IPv6 Unicast: Static Routing(Software Base) IPV6 IPv6 neighbor discovery (ND) Path maximum transmission unit (MTU) discovery Internet Control Message Protocol (ICMP) version 6 TCPv6/UDPv6 Ping6 Telnet(v6) Http/Https Interface IPV6 ACL IPV6

SDR-240-24 Für DIN Rail, Hutschiene Eingang: 88~264VAC, 124~270VDC Ausgang: 10A, 24V DC (24~28V) Umgebungstemperatur: -25°C ~ +70°C LxBxH 63x125,2x113,5mm Schutzkennzeichen: Siehe meanwell.com weitere Details bitte dem Datenblatt entnehmen