Bricks

LED BRICK mit 4 highpower LEDs.

A button is an electromechanical element which connects when pressed.

This brick is based on the LED brick WS2812B. Controlling it is identical with the digitally controllable RGB LED brick. This brick is mainly used to redirect several digitally controllable RGB LED bricks about 90° or in two different directions. The ALL-BRICK-0377 can be supplied with 7-24V and needs about 65mA.

With the corner you can connect your wires via corner.

Rote ((Gelbe) (Blaue)) 4mm Buchse für Bananenstecker. Die Verbindung geht durch den Brick. Die 4mm Buchse ist "Inline" damit verbunden. Die beiden inneren Kontakte der Hermastecker sind miteinander verbunden. Maximaler Strom 12A.

The straight wire connects two opposing Bricks left with right and top with bottom, without connecting the two wires.

Our switch includes three different states: In the middle state, all contacts are separated. In the left state, there is a connection between the middle and the left. And in the right state there is a connection between right and middle. A maximum of 6A is possible.

LED RGB Farben werden mittels 3 Potis eingestellt

Both of the middle contacts of the plugs are connected to the contacts of the clip. Additionally, there is one clip for the ground.

The basic set's manual involves explanations for every brick that is included in the set. It also includes examples for electric circuits that can be rebuilt or used as inspiration for new ideas.

The straight wire connects two opposite Bricks.

Both of the middle contacts of the plugs are connected to the contacts of the clip. Additionally, there is one clip for the ground.

Dual duplexer left/right to be used with Flip Flop, Arduino or Logic Bricks.

Brick to integrate external I²C sensors and actuators in circuits including Arduino / Banana bricks as in our coding set. The brick has a precise, stable voltage of 5V and 3,3V for the sensors. The internal voltage sources can be used with a total of 100mA to provide the sensors. The brick's supply voltage is 9V.

Das Potentiometer ist ein Widerstand mit einem veränderbaren Abgreifer. Es hat drei Anschlüsse. Der Widerstand bezieht sich auf den Wert der festen Größe. Der Abgreifer kann mechanisch bewegt werden und liefert einen Wert zwischen dem geringsten und maximalen Widerstandswert an der dritten Klemme. Das Potentiometer hat auch eine maximale Leistung - bei uns ca. 1/8 Watt - die leicht überschritten werden kann, wenn man den Abgreifer direkt mit der Spannungsquelle und einem der anderen beiden Anschlüsse verbindet.

Special connector that is able to lead signals (that use one contact only) to bricks that include two connected contacts. Usually used when interconnecting logic bricks and connection between Arduino/Banana brick with the typical eletronic bricks from the Advanced Set.

A resistor has a defined conductivity, which determines the current when voltage is applied. The maximum load is important, which is converted to heat – for our resistors this should not be more than 1/8W.

This manual is included in the Advanced Set and contains a number of sample circuits for orientation, if you don’t know how to carry on or of you are looking for new ideas.

Board to be fitted with desired components. Each Herma-connector has its middle pins individually available on the board. There is an additional slot on one site to solder in a P-SMP or SMA pin. On the upper site: SMD pads with 2.54mm grid. On the lower site: SMD pads with 1.27mm grid.Through holes between upper and lower site.

The universal base can be used if certain components are not included in the set. If you for instance need a 9.8kOhm resistor, you can simply attach it to the universal base.

Ein Widerstand besitzt eine definierte Leitfähigkeit, die bei einer angelegten Spannung den Strom festlegt. Wichtig ist die maximale Leistung, die dabei in Wärme umgewandelt wird - bei unseren Widerständen sollte sie nicht mehr als ein 1/8Watt betragen.

With Brick'R'knowledge from tube to microcontroller Brick'R'knowledge's inventor about the book: With Brick'R'knowledge's modular bricks it is easy to do experiments and pass on knowledge about electronics. The book elaborates on that by developing new bricks to realize certain functionalities. This way, a number of new experiments is possible. The book covers everything from simple measuring instruments to processors that control the developed system. The book also deals with tube technology that is used, nowadays, in the industry when dealing with power. With the bricks, it is very easy to rebuild, understand and modify tube circuits. The book is meant for everyone who is interested in electronics, covering various experiments that provide you with a deeper understanding of technology.