Synergy 21 LED Controller 3653 LED RGB-WW (RGB-CCT) Master Set

Erweiterung Slave 3654 für Master 3653 Anschlüsse: Power: 12Volt oder 24Volt (Klemmen im Lieferumfang) Leistung: bis zu 10A LED Ausgang: R G B W1 W2 (Klemmen im Lieferumfang) Master Slave Verbindung: RJ-45, CAT3 oder CAT5 max 20m Größe: 110*50*28mm Gewicht: 80g

Extension hub / distributor for PL3653 master and PL3654 slave Connections: Power: not necessary 8*outputs/1*input: 9*RJ-45, freely selectable Master slave connection: RJ-45, CAT3 or CAT5 max 20m Size: 165*35*28 Weight: 100g Attention: only one distributor per zone is possible

RGB-W Flex-Stripe, 5 metres, RGB and warm white on one chip Warm white: 2500K ±250 DC 24V, 90W, 25Watt ww, 65Watt RGB, 3.75A max. Brightness: ww 1500lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*10*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (10 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed the working temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe, 5 metres, RGB and warm white on one chip Warm white: 3000K ±250 DC 24V, 90W, 25Watt ww, 65Watt RGB, 3.75A max. Brightness: ww 1600lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*10*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (10 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed the operating temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe, 5 metres, RGB and neutral white on one chip Neutral white: 4000K ±250 DC 24V, 90W, 25Watt nw, 65Watt RGB, 3.75A max. Brightness: nw 1750lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*10*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (10 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed an operating temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe, 5 metres, RGB and cool white on one chip cold white: 6200K ± 10% DC 24V, 90W, 25Watt nw, 65Watt RGB, 3.75A max. Brightness: cw 1750lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*10*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (10 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed an operating temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe - s-shape, 5 metres, RGB and warm white on one chip Warm white: 3000K ± 10% DC 24V, 90W, 25Watt ww, 65Watt RGB, 3.75A max. Brightness: ww 1600lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*12*2,2 for indoor can be shortened: all 6 LEDs can be shortened (12.5 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed the operating temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe - s-shape, 5 metres, RGB and warm white on one chip Warm white: 2500K ± 10% DC 24V, 90W, 25Watt ww, 65Watt RGB, 3.75A max. Brightness: ww 1500lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*12*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (12.5 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed the operating temperature of 40°C, otherwise the service life cannot be guaranteed.

RGB-W Flex-Stripe - s-shape, 5 metres, RGB and neutral white on one chip Neutral white: 4000K ± 10% DC 24V, 90W, 25Watt nw, 65Watt RGB, 3.75A max. Brightness: nw 1750lm ± 10% 300 PCS 5050 SMD LED common positive pole L*W*H: 5000*12*2.2 for indoor use can be shortened: all 6 LEDs can be shortened (10 cm) Adhesive tape for mounting aid on the back Control via Portaluce controller or RGBW controller (radio, DMX, etc.) Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed an operating temperature of 40°C, otherwise the service life cannot be guaranteed.

Colour selection between 3000-7000K possible with controller ww: 3000K ±250, cw: 6500K ±250 5 metres, (5000*10*3mm) 24 Volt, common positive pole, 96 Watt total 6000Lm 600 high power 3528 SMD LED, double LED, with ww+cw on one chip DC24V, 48W per colour, nonwaterproof IP20 Can be shortened every 12 LEDs (50mm), Adhesive tape for mounting aid on the back Strip can be shortened at markings with sharp scissors. !Attention! Strip must first be checked for functionality. Only split the strip when no current is present. Energy efficiency class: A kWh/1000h: 96 Please note that LED strips must also be cooled. Make sure that the LED strip does not exceed an operating temperature of 40°C, otherwise the service life cannot be guaranteed.

Temperature measurement via network easy made Highlights: detection of Temperature / Humidity / Gas / Smoke / Movement etc. via network Robust metal housing Brackets for attachment to wall Suitable for all operating systems 1x ALL3006 Temp-Sensor including Flexible/Multiple Installation of different ALLNET Bulding-Automation Units can be controlled in one Web-GUI with JSON API Optional Free-Software Modules like SNMP  / FTP Upload / POST_GET / Upload into PoE Clock/Counter / EnOcean / The ALLNET ALL3419 IP Thermometer/Automation-Building-Main-Unit is a flexible and economical solution for temperature measurement over a network. The very compact design makes it suitable for use in confined spaces. The rugged metal housing has tabs for mounting on walls and ceilings and protects against mechanical damage. The ALL3419 IP Thermometer/Automation-Building-Main-Unit is connected to a computer network via cable or WLAN and is accessible by an IP address. The measured values ??can be accessed via web browser on the device itself. No additional software is required for operation. Thus the ALL3419 is appropriate for all operating systems. The temperature is measured by the included I2C RJ45 temperature sensor ALL3006. Another internal onboard sensor shows the internal system temperature. With the optional ALL3018 temperature & humidity sensor can detect also humidity. The measurement intervals can be set second by second. The last 512 values can be shown directly as a graphical trend. Additional Sensors and Actors can be also measure Gas / Movement etc. see http://www.allnet.de/en/allnet-brand/produkte/home-automation/home-automation-sensoren/ Intelligent features and programming by switching matrix Depending on measured values certain actions can be programmed over the software based switching matrix. For example, if temperature is above or below defined limits, the readings can be sent by email. This may once, several times, and/or in certain time intervals, so long as the matrix condition exists. Another possibility is switching of external IP switching devices, such as network-sockets series ALL307x or network-relay ALL4075/4175 as well as directly connected actuators, for example the relay module ALL4427/3527. Alternativly can be switches also over the JSON Protocol.   Flexible installation options The external sensors can be plugged directly on ALL3419 or can be connected remotely via a control line. For remote connection a simple network cable (RJ45 connector, Cat. 5) is suitable to connect the sensors with the CPU. This way of connection is used in all ALLNET Home Automation products. For this purpose, an existing cable network such as already installed network or telephone lines can be used. The maximum cable length between CPU and sensor module can be up to 100 meters. The power supply of the sensor modules is already done via the main unit. A separate power source for each sensor module is not necessary.   Borderless Cross-site temperature measurement Several ALL3419 can operate in conjunction with the bigger control and measurement computers ALLNET ALL3500/3505/4500 or ALL5000, to show a lot of geographically distributed values in a centralized way. Each individual ALL3419 is queried over an individual IP address and centrally stored and displayed in all the other Main-Units like ALL3418v2/3419/3500/3505/4500/5000 etc. Maximum number of sensors per ALL3419:       Element Specification Sensor interface: 3x RJ45 for sensor/actor modules 1x USB 2.0 for additional Wireless Dongles like "EnOcean or Plugwise" 1x RJ45 Console Port for Serial-Connection Ethernet: 1x RJ45 10/100Mbps Wireless LAN: Ralink/Mediatek MT7688AN 2,4 GHz Wireless N, up to 150 Mbps Security: WEP 64/128bit, WPA, WPA2 Standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Power source: 100~240 VAC, 50/60 Hz Power Consumption: <3 watt in operation Housing: metal housing Environment: Operating temperature: 0 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 70 °C Storage humidity: 5% ~ 90% (non-condensing) Regulatory: CE, RoHS Dimensions: 92 x 85 x 24 mm (L x W x H)  Weight: 134 g (ALL3419 with ALL3006 sensor) Package content: -ALLNET ALL3419 -ALLNET ALL3006 temperature sensor -WLAN antenna -External power supply -Quick installation guide

Your smart entry into building automation – ALLNET ALL3500v2 With the ALLNET ALL3500v2 building automation centre, you get a cost-effective and versatile platform that is optimally tailored to semi-professional requirements. Thanks to state-of-the-art technology, high connectivity and a wide range of applications, the ALL3500v2 is the perfect partner for your automation projects. Highlights at a glance: Cost-efficient platform: Maximum functionality with minimum space and cost requirements. Intuitive operation: Can be conveniently controlled via web interface (HTTP/HTTPS) or smartphone. Flexible data connection: Integration via JSON, MQTT or SNMP possible. Versatile sensor technology: Comprehensive monitoring of temperature, humidity, air pressure and more. Future-proof: Expandable with i2C sensor ports and compatible with a wide range of ALLNET sensors and actuators. Features that impress The ALL3500v2 is based on a stable embedded Linux platform (MIPS or ARM architecture), which enables seamless integration into existing systems. With four RJ45 ports for sensor modules, you can realise a wide range of control and monitoring tasks. Whether local control or cloud-based applications - the ALL3500v2 offers you all the tools you need to organise your building automation efficiently and securely. Versatile application options: HACCP temperature monitoring: Precise detection and control in critical environments. Room climate control: Monitoring of temperature and humidity for demand-based control of heaters or humidifiers. Security management: Detection of gas odour, smoke or water ingress and triggering of alarms. Automated garden irrigation: Time and humidity-controlled for maximum efficiency. Energy consumption optimisation: Control based on consumption data from external sensors (e.g. ALL4590/4490 power meter). Compact, powerful, versatile The ALL3500v2 combines a variety of functions in a compact design that has been specially developed for space-saving installations. With four relays, sensor ports and contact interfaces, it can be used flexibly and provides the basis for sophisticated automation solutions - ideal for private and commercial applications. Why ALLNET ALL3500v2? With the ALL3500v2 you get a reliable and economical solution for building automation. From monitoring and control to integration into complex installations, this central unit offers everything you need for smart, efficient and future-proof automation. Start your building automation now with the ALLNET ALL3500v2! Versatile sensors, actuators and switching options for your automation The ALLNET ALL3500v2 impresses with its flexibility and functionality: With four ports for external sensors and actuators, four relay outputs for controlling loads and four contact inputs for buttons or switches, it provides an ideal basis for complex automation applications. Sensing and control – Precise and versatile With the ALL3500v2, you can measure and analyse a variety of environmental parameters such as temperature, humidity or air pressure and execute automatic switching operations based on them. Control is either manual, time-controlled or dynamic, based on the measured values. Connectivity that inspires The ALL3500v2 is equipped with Ethernet and built-in WLAN, which enables easy integration into existing networks. Using an IP address in the TCP/IP network, you can: Retrieve and edit measurement data directly in the web browser. Receive automated notifications and reports by email. Request and control data via JSON or XML interfaces. Optional MQTT support enables the transmission of data to the cloud and integration into IoT environments. With its powerful connectivity and flexible control options, the ALL3500v2 is the perfect choice for efficient and future-proof building automation.   I²C-Bus – Intelligent use of existing cable networks The ALLNET ALL3500v2 enables an uncomplicated connection of measurement and control modules via a standard network cable (RJ45, Cat. 5). This allows you to continue using existing cable infrastructures such as network or telephone cabling and saves costs and effort during installation. Advantages of the I²C bus system: Simple cabling: A standard network cable is sufficient to connect sensors and modules. Long range: Up to 100 metres of cable between the central unit and module. Integrated power supply: The modules are supplied with power directly from the central unit – no separate power source required. USB port – external memory connection The USB port on the ALLNET ALL3500v2 allows you to integrate external storage media easily and flexibly. This allows data to be saved and processed directly on connected USB devices. This enables extended data logging and analysis. Maximum number of sensors per ALL3500v2: Technical data: Element Specification Interfaces: 4x RJ45 for sensor modules Network connection: 1x RJ45 10/100Mbps Switching relay: 4x potential-free Contact input: 4x for push-buttons, switches, etc. Wireless LAN: Mediatek MTK7688 SOC chipset 2.4 GHz Wireless N Security: WEP 64/128bit, WPA, WPA2 Supported standards: IEEE 802.3 IEEE 802.3u IEEE 802.11b/g/n Other interfaces: 1x USB 2.0 1x console Power supply: 100~240 VAC, 50/60 Hz, external power supply Power consumption: <5 watts maximum How to use: Metal walkway Environment: Operating temperature: 0 ~ 40 °C Operating humidity: 10% ~ 85% (non-condensing) Storage temperature: -20 ~ 60 °C Storage humidity: 5% ~ 90% (non-condensing) Labelling: CE, RoHS Dimensions: 220.4 x 80 x 30 mm (length x width x height) Weight: 400 grams (device incl. WLAN antenna and ALL3006 sensor) Packaging contents: -ALLNET ALL3500v2 -ALLNET ALL3008 temperature sensor -WLAN antenna -External power supply -Operating instructions

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting   Measure, control and regulate automatically and independently   ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs.   Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location.   The ALL4432 Brightness sensor indicates the brightness as value of 0 to 100.   Brightness Sensor in desktop-/ wallmounting case   measuring range of 0 to 100 Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Brightness analog 16bit measuring range: 0 to 100 Chip ADS1100A2 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4432 Brightness sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights: new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use either black or white available angle fixings for wall mounting Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4432 Brightness sensor indicates the brightness as value of 0 to 100.   Brightness Sensor in desktop-/ wallmounting case measuring range of 0 to 100 Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 (not compatible with ALL3000/400x) Technical Details: Item Specification Sensor type Brightness analog 16bit measuring range: 0 to 100 Chip ADS1100A2 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: pay attention about the same types of sensors on the port! -  see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4432 Brightness sensor 1x connection cable Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4452 PIR Movement detector has a max. detection angle of 92° and a max range of 8 meters. Movement detection Sensor in desktop-/ wallmounting case max. detection angle of 92°, max. range of 8 meters Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 Technical Details: Item Specification Sensor type   PIR movement detection   measuring range: max. detection angle of 92°, max. range of 8 meters Chip PCF8574 Interfaces: 2x RJ45 (I2C Bus) Multiplexing:   dial wheel for ID (8), see note below   LED Indicators: 1x PWR, 1x BUS, 1x Detetct Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4452 PIR Movement detection sensor 1x connection cable   Multiplexing - Note to the operation of several sensors on one sensor port Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more thanone sensor on a physical port. Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby. So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.

- compatible with ALL34xx/350x/4500/5000 - Measuring range -40...+125 °C, 0...100 %RH - resolution temperature 0,01 °C, resolution humidity: 0.01 % - Measuring accuracy Temp in whole range approx. +/- 0,6° (Typical: -20 + 90° = +/- = 0,2°) - Measuring accuracy humidity in the whole range approx. +/- 3% (Typical: 0~80% +/- 1.5%) - With 1.5 m connection cable Technical Details: Humidity Sensor Specification Parameter Condition Value Units Sensor Humidity Accuracy tolerance1 Typ. ±1.5 %RH Max. -   Repeatability2 Low, typ. 0.21 %RH Medium, typ. 0.15 %RH High, typ. 0.08 %RH Resolution Typ. 0.01 %RH Hysteresis at 25°C ±0.8 %RH Specified range3 extended4 0 to 100 %RH Response time5 t63% 86 s Long-term drift Typ.7 <0.25 %RH/yr       Temperature Sensor Specification   Parameter Condition Value Units ALL3020 Accuracy tolerance1 typ., 20°C to 60°C ±0.1 °C Max. -   Repeatability2 Low, typ. 0.15 °C Medium, typ. 0.08 °C High, typ. 0.04 °C Resolution Typ. 0.01 °C Specified Range - -40 to 125 °C Response time 8 t63% >2 s Long Term Drift max <0.03 °C/yr

Temperature sensor for ALL3000/34xx/3500/400x/4500/5000 WATERPROOF & salt water resistant Measuring range -55 to +125 °C Resolution 0.06°C 1m silicone cable with shrink cap with RJ45 Keystone socket "Art. 88971" The scope of delivery also includes 1x 20m patch cable.  

Temperature sensor compatible with ALL3000/34xx/3500/ALL400x/4500/5000 Measuring range -55 to +80 °C, 13-bit ADC with a temperature resolution of 0.03125 °C Temperature accuracy of ± 1 °C from -25 °C to +100 °C with 1 m connection cable Exclusively only one of the following sensors possible per sensor port! ALL4454, ALL4432, ALL4421, ALL4590, ALL4532, ALL4552, ALL4522, ALL3005-6, ALL3015,ALL4006, ALL4506-7  

Highlights:   new compact aluminum desktop- / wallmounting case I2C Bus for multiplexing use angle fixings for wall mounting   Measure, control and regulate automatically and independently ALLNET for years been pursuing the concept of intelligent control of processes in building over network and Internet. Intelligent building not only offers comfort, but actively promotes the reduction of energy costs. Centrally managed and via network / internet accessible the ALLNET Home Automation products allow intelligent building automation regardless of time and location. The ALL4429 Combination sensor has a measuring range of 0 to 1023 mbar, -40 to +80 °C and 0...100 % RH Combination Sensor of air pressure/humidity/temperature in desktop-/ wallmounting case measuring range of 0 to 1023 mbar / -40 to +80 °C (resolution 0,01 °C) / 0...100 % RH (resolution 0,5%) Aluminum housing with bracket for wall mounting Multiple multiplexing = multiple modules on one line Interfaces: 2x RJ45 not compactible with ALL3000/ALL5000 Technical Details: Item Specification Sensor type air pressure, humidity, temperature air pressure measuring range: 0 to 1023 mbar Temperature measuring range: -40 to +80 °C  (resolution 0,01 °C) Humidity measuring range: 0...100 % RH (resolution 0,5%) Chip BMP085 + SHT71 Interfaces: 2x RJ45 (I2C Bus) Multiplexing: see note below LED Indicators: 1x PWR, 1x BUS Housing: metal case Environment: Temperature operating: -45 ~ 90 °C Humidity operating: 0% ~ 100% (non condensed) Temperature storage: -20 ~ 60 °C Humidity storage: 5% ~ 90% (non condensed) Certificates: CE, RoHS Dimension: 79 x 50 x 24 mm (Length x Width x Height) Weight: 230 Grams (only device) package content: 1x ALL4429 Combination sensor 1x connection cable     Multiplexing - Note to the operation of several sensors on one sensor port   Basically, it is for the ARM and MIPS-based systems possible, unlike to the ALL3000/4000 to operate more than one sensor on a physical port.   Standard hardware requirement is that the sensors are equipped with 2 RJ45 connectors so that the sensor signal can be continued to the next sensor. The total cable length of 100 m does not increase thereby.   So that the sensors can be uniquely identified by the devices, it is necessary that these sensors have different software-I2C chip addresses and IDs. Sensors with the same address and adjustable chip ID can be combined. For sensors without adjustable ID address only one type of sensor can be connected per port.  

-compatible with ALL3418v2/3500/3505/4500/5000 -0-10V dimming output with ON/OFF relay (10A) for 0-10V power supplies -Aluminum housing with bracket for wall mounting -Connections: 1x RJ45 input / 1x RJ45 output -(no longer compatible with ALL3000/400x)

EnOcean dimmer switch (batteryless / wireless) For receivers of the EOS 09 series or other EnOcean devices Operating temperature: -20°C - +50°C CE/FCC/RoHS Protection class: IP20

EnOcean dimmer switch for dual white LED products (battery/wireless) For receivers of the EOS 09 series or other EnOcean devices Operating temperature: -20°C - +50°C CE/FCC/RoHS Protection class: IP20

IP Symcon Basic is the center of your digital world of technology.It combines a variety of household devices, computer accessories or audio & video components under a software interface. Using blocks can be used without programming skills on graphic way, only with the mouse a control problem can be solved. Sensors, actuators, timers and logic modules can be linked together. After checking in a simulation to use in practice, nothing stands in the way. IP Symcon is the interface between a PC and various actuators and sensors.It is an industry-and technology-neutral system for solving visualization and tax-related tasks in the home automation and process automation. IP Symcon provides function modules for control and regulation, reporting, archiving and logging (graphic representation, database). With its powerful coupling to a variety of hardware modules and the secure data archiving it ensures high availability.The IP Symcon software allows any custom shortcuts of events and measurements of building services equipment (e.g. ALL3xxx and ALL4xxx family), programming via PHP scripts, and configuration graphical user interface for visualization of measurement data and operating procedures and much more.Maximum numbers of variables: 250Maximum number of devices: unlimitedTime limitation: unlimitedFeatures and Compatibility:ALLNET ALL30xx / ALL40xx seriescompatible to FHZ 1X00 PC     FS20-Receriver     FS20-Transmitter   HMS (House and alarm system)     KS300 weather sensor   FHT80b (Heating control)     433MHz weather-system of ELV (in conjunction with the PC-weather receiver WWWReader/Text Parser   -  Front-End: Web-Server & IPS-Designer     EIB (European Installation Bus) > Interface PEI Typ 10 mit FT1.2 Protokollserial interface (com-port)     1-Wire components (inter alia: DS1820 / thermometer, DS2450 /A/D-converter)XComfort of Moeller     ISDN - (Capi / DTMF Sounds/Voice)     DMX - Lighttechnology ( DMX4ALL)     enocean® PTM200, STM100, TCM120     SIEMENS: GIGASET WebCam, M34 USB     Sound Files & Voice output (DirectX Media Player / Winamp)     technical alternative UVR1611, Schüco VARIO     memPIO (BMC measurement)     MEILHAUS - RedLab     VELLEMAN - USB - Experimentation and interface board     BTkit, IRtrans, LIRC compatiblel > IR - remote control     WAGO / Beckhoff SPS       System-requirements: PC - IBM compatibleOperating Systems Microsoft Windows 2000/XP/VistaRAM minimum 256 MB100 MB free hard disk spaceDownload VersionInternet connection required

Building automation Have you ever wondered why, although your phone a missed call displays, while, however, a visitor made ??his way to the front door in vain if you are not there? Or is it already happened to you, that the time-controlled shutters have you locked out while you still enjoyed the mild summer evening on the patio? Have you ever seen the roof windows are left open, when it began to rain suddenly, and nobody's noticed? Or are you still standing in winter every day an hour earlier to vain to wait for the announced winter? Do not you wish sometimes even an artificial intelligence that thinks for you? IP Symcon is the answer to this problem. Cross-manufacturer There are many different systems of the industry , making it possible to do a variety of things for you in the house. Blinds manufacturers equip their products with out remote controls, a manufacturer of electrical equipment bring solutions for intelligent light control on the market, multifunction remote controls simplify operation of various entertainment media and heater manufacturers have extensive controls integrated. The problem is that these different solutions, so innovative it may be, either alone work very well, but not together. IP Symcon "a bridge" between these systems so that they work as a single. It is therefore possible from now on with a normal light switch, to control not just the light, but also blinds, heating and music. But that is far from the end: Control the home theater, the indoor climate and let you wake up, depending on the actual outside temperature in the morning with your favorite radio station. Energy saving It has by now gotten around, that the standby mode at night unnecessarily consumes a lot of energy. You can certainly use IP Symcon to turn off TV and DVD player overnight or to regulate the heating down at night. And not so as it will enable many simple operating units: e.g. always 20 clock, but then when you're actually gone to bed - even if it's become late. In addition, you can display your power consumption graph. Savings can be determined and identify power-hungry so easily. This will save you smart electricity, gas and oil, and on top of that you enjoy the comfort of IP Symcon. Comfort With IP Symcon you can easily create special lighting scenarios for living, working or watching TV and drive. Mood lighting provide a cozy feeling, but for crafting or reading you need a lot of light. Do not longer run through the entire apartment to several reading lamps and cabinets or television lighting on and off. Just press a button and everything shines as desired. Perhaps, however, not only by remote control touch screen next to the couch, but also via mobile phone or iPod via WiFi? From home or away? You are the director. Safety Keep track of who was at your front door. Secure your door with a code number or open the apartment door with a smart card. If someone took to create it, you will receive an SMS to your phone. The video intercom also shows you, no matter what, is going on. To open the door with the fingerprint is Science Fiction? Not with IP Symcon. Motion detectors in individual rooms not only ensure that the light is switched, they are when you want, simultaneously coupled with your alarm system. Window and door contacts provide additional security. When leaving the house, you will be notified when a window is still open or the back door is not closed. Visualization How to keep track of so much technology? With IP Symcon you get a comprehensive visualization package. Design your own user interface. With the IP Symcon Dashboard, you can completely create without programming knowledge comfortable user interfaces for the PC or a touch panel in the kitchen. Access is also possible from a distance via the Internet. Whether you prefer a clear plan of his apartment or the style of a classic website, is only limited by your own imagination. Or do you prefer to work in the browser? About using the included web server you call in the browser on your own, designed in PHP and HTML, home control sites. Just as you would build their website. For the built-in web server provides IP Symcon. For those who like it even easier, there's also the IP Symcon WebFront. Here is the keyword "zero configuration". Without even doing a handshake, you can here, "Out of the Box" control your home automation via the browser using AJAX. From home and elsewhere. But that's not all. Let generate graphs and trends and give you not only keep track of your energy consumption or the precipitation of the last month. Always up to date!     More Details: